Chemical process industries use complex equipments. Some of these are fractional distillation columns, catalytic cracking reactors, and bioreactors. In the bioreactor of one industry, the reactions below can occur to perform the fermentation process. The tank is initially charged with 7500 kg of 18% solution of glucose in water. After fermentation, 170 kg of CO2 produced and 100 kg of unreacted glucose left in the broth. Use atomic species balance in solving. C6H1206 - C2HSOH + CO2 CGH1206 - C2H3CO;H + H2O A. How much water is there in the tank after fermentation? B. How many moles of C2H12O6 reacted in the first reaction? C. How much Ethanol is there in the product in kgs? D. How much propenoic acid is there in the product in kgs? E. How many kgs of C2H1206 is used in second reaction?

Chemical process industries use complex equipments. Some of these are fractional distillation columns, catalytic cracking reactors, and bioreactors. In the bioreactor of one industry, the reactions below can occur to perform the fermentation process. The tank is initially charged with 7500 kg of 18% solution of glucose in water. After fermentation, 170 kg of CO2 produced and 100 kg of unreacted glucose left in the broth. Use atomic species balance in solving. C6H1206 - C2HSOH + CO2 CGH1206 - C2H3CO;H + H2O A. How much water is there in the tank after fermentation? B. How many moles of C2H12O6 reacted in the first reaction? C. How much Ethanol is there in the product in kgs? D. How much propenoic acid is there in the product in kgs? E. How many kgs of C2H1206 is used in second reaction?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 0.512 g sample of a commercial phosphate detergent was ignited at a red heat to destroy the organic matter. The residue was taken up in hot HCl, which converted the P to H3PO4. The phosphate was precipitated as MgNH4PO4.6H2O by addition of Mg2+ followed by aqueous NH3. After being filtered and washed the precipitate was converted to Mg2P2O7 by ignition at 1000 0C and the residue weighed 0.1151g. (a) What is the Gravimetric Factor to convert Mg2P2O7 to P? (b) Calculate the percent P in the sample could you type it out please
A hydrocarbon stream composed of 40 mol% n-butane and 60 mol% n-octane is fed at 100 kmol/h to a flash vessel operating at 5 bar and 145°C. The liquid outlet stream of the flash vessel is then sent to a distillation column with a partial condenser to further separate the components. 90% of the butane in the feed to the column is recovered in the overhead vapor product (distillate), along with small amounts of octane. The bottoms product contains octane which accounts for 75% of the octane in the fresh hydrocarbon feed (to the flash vessel). The condenser and reboiler operating temperatures are 136.7°C and 165.7°C, respectively. Determine the compositions of the liquid outlet stream of the condenser and the vapor outlet stream of the reboiler.
A mixture of methane and air is capable of being ignited only if the mole percent of methane is between 5% and 15%. A mixture containing 9.0 mole% methane in air flowing at a rate of 7:00 x 102 kg/h is to be diluted with pure air to reduce the methane concentration to the lower flammability limit. Calculate the required flow rate of air in mol/h and the percent by mass of oxygen in the product gas. (Note: Air may be taken to consist of 21 mole% O2 and 79% N2 and to have an average molecular weight of 29.0.)
A water-carbonating plant is available for use in the home and operates by providing carbon dioxide at 1.0 atm. Estimate the molar concentration of the CO2 in the soda water it produces.
It is desired to determine the molecular weight of an organic compound known to be volatile. For this, a glass balloon with a full volume of 152 mL is weighed and the weighing result is recorded as 215 g. Then, the organic compound that is desired to have some molecular weight in liquid form is added into the balloon and evaporated in a water bath until dryness. After the steam temperature is measured as 90 °C, the balloon is left to cool and the organic compound in the balloon condenses again. The balloon is then weighed again and recorded as 215,367g. Find the molecular weight of this organic compound since the pressure of the environment where the experiment is performed is 700 mmHg.
1. Sodium carbonate is recovered as decahydrate from 1000kg of 5% solution of sodium carbonate in water. If it is desired that 95% of Na2CO3 is to be recovered as decahydrate by cooling to 278 K, determine the following: a) the mass of water evaporated (b) the mass of crystals obtained (Na2CO3 ∙ 10H2O). The solubility of Na2CO3 in water at 278K is 9.0% (weight) 2. A copra batch contains 44% oil and is to be extracted with n-hexane. The extracted meal contains 0.07 kg of oil/kg oil free matter and the mass fraction of n-hexane in it is 0.05. The extract contains 49% n- hexane. If 10,000 kg of copra are to be processed, how many kg of n-hexane are required and the determine the amount of extract. 3. Absorption of sulphur dioxide is carried out in a packed tower. Gas containing 14.8% sulphur dioxide and the rest inert gases enters the tower while the leaving gases contains 1% sulphur dioxide. Water flows at the rate of 1m3/min. The tower handles 7380 m3/hr of gas at 303K and 1 bar. Find…
The separation of aromatic compounds from paraffins is essential in producing many polyesters that are used in a variety of products. When aromatics and paraffins have the same number of carbon atoms, they often have similar vapor pressures, which makes them difficult to separate by distillation. Extraction is a viable alternative, as illustrated by the following simple system. Sulfolane (an industrial solvent) and octane may be considered completely immiscible. At 25°C, the ratio of the mass fraction of xylene in the octane-rich phase to the mass fraction of xylene in the sulfolanerich phase is 0.25. One hundred kg of pure sulfolane are added to 100 kg of a mixture containing 75 wt% octane and 25% xylene, andthe resulting systemis allowedto equilibrate. How much xylenetransferstothe sulfolane phase?
Nitrogen is to be liquefied in a simple Linde process. The feed and recycle are mixed. compressed to 64 bar, and precooled to 135K. The vapor then passes through a heat exchanger for additional cooling before beinng throttled to 1 bar. The unliquefied fraction leaves the seperator at the saturation temperature and passes through the heat exchanger, then exits at 120 K. a. What fraction of the gas is liquefied in the process? b. What is the temperature of the high pressure gas entering the throttle valve?
L-lysine is produced by Corynebacterium glutamicum in a bioreactor using glucose as the carbon source and ammonia as the nitrogen source. All streams of this process are aqueous. In the inflow, 8 grams of glucose per 100 grams of flow fluid flowing at a rate of 500 kg / hour is included. The glucose flow rate in the exit steam is 1 kg / hour. The reaction takes place at 25 °c.What is the mole percentage of glucose that was consumed during cell growth inside the bioreactor? -Does the growth of Corynebacterium glutamicum cells inside this bioreactor release or absorbheat? Should heat be supplied to the bioreactor, or removed from, to maintain the operation temperature? I want the solution of both options.
A water carbonating plant is available for use in the home and operates by providing carbon dioxide at 5.0 atm. Estimate the molar concentration of CO2 in the carbonated water it produces.
Stoichiometry is a significant part of chemical engineering. In industrial practice, stoichiometry followed by material and energy balances (MEB) is particularly important for each unit process/operation. This task focuses on the understanding of a chemical operation and its input-output stream characteristics involving MEB adapted in the entire process. select any sub process from a major unit and complete the following tasks Process Flow Diagram and stoichiometry Provide the complete Process Flow Diagram (PFD) and explain the concept of stoichiometry including the calculations involved in the process
Chlorodifluoromethane (CHF2Cl) was widely used in the compression/cooling circuits of refrigeration or air-conditioning systems. Since the discovery that such compounds (HCFCs and CFC's) released into the atmosphere were a major cause of depletion of stratospheric ozone, newer refrigeration systems make use of certain hydrofluorocarbons (HFCs), which are degraded in the lower atmosphere, instead. Often, mixtures of such compounds are used. Suppose a sample of refrigerant gas consisting of a simple mixture of the gases pentafluoroethane (C2HF5) and difluorormethane (CH2F2) has a density of 3.06 g/L at 14 °C and 0.974 atm. Calculate the average molecular mass for this sample