Chemistry Am I suppose to have a straight line in a standard addition plot? Specifically, I am graphing my data obtained determining Mn in steel using spectrophotometry. I used the Method of Standard Addition to perform the lab. I preform the lab twice and my data goes up and down; however, I was under the impression it was supposed to be a straight line

Chemistry Am I suppose to have a straight line in a standard addition plot? Specifically, I am graphing my data obtained determining Mn in steel using spectrophotometry. I used the Method of Standard Addition to perform the lab. I preform the lab twice and my data goes up and down; however, I was under the impression it was supposed to be a straight line

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter28: Atomic Spectroscopy

Section: Chapter Questions

Problem 28.14QAP

See similar textbooks

Similar questions

Which among the options for minimzing errors (Separation, Saturation-Mix Modification-Masking, Dilution and Matrix Matching, Internal Standard Methods, Standard Addition Methods) is most helpful with more advantages than disadvantages?
List three typical examples applications of SFC analysis.
Fluoride determination can be performed photometrically with alizarin red and Zirconium acid solution, obtaining the following data in the calibration: (View Table) 100.0 mL of well water are measured and concentrated to 50 ml by evaporation, the alizarin and zirconium reagents are added (in quantity proportional to the standards) and after the appropriate time, the reading of the instrument (under the same conditions instrumental) reports an absorbance of 0.182. How much fluoride in mg / L does the well water sample contain?
Retention time is the time taken for the mobile phase to reach the detector. True False
The standard addition technique was used for the voltammetric analysis of a Cd2+ sample. From the data listed in the table below, calculate the concentration of the Cd2+ in the sample. Added concentration, mM 0 1.2 2.5 4.04 6.00 7.5 Absorbance 3.8 5.5 7.2 9.5 12.2 14.3
What are method blanks and method detection limit used in analytical chemistry? Explain thoroughly
If some of the analytes were found to be out of range after doing the Quality Control and the machine repeatedly gives invalid result. What are the possible problem and best solution as a Medical Technologist?
Give the advantages and disadvantages of sequential injection analyzers compared to traditional flow Injection analyzers.
Please help me I am looking forward of a list (3 sources of error and explain it)
The determination of iron in wines was carried out by atomic absorption spectrophotometry, using the standard addition method. To do this, 10 mL of wine were placed in five 50 mL volumetric flasks; then 0, 5, 10, 15 and 20 mL of a 10 ppm iron standard solution were added to each of them. Next, they were gauged with distilled water and the absorbance was measured, obtaining the values of 0.040, 0.062, 0.081, 0.102 and 0.125 respectively. Calculate the regression parameters and obtain the iron concentration in the wine, in µg / mL.
10 m2 with 7-micron silver coating only in certain areas on I total 50 m2 surface field copper materials were scrapped. The recovery of silver is only correct It is economical with the reactor design and under the condition of a suitable reagent selection. A- H2SO4 B- HNO3 C- HCl 1. Write down all the reactions that will occur for these acids. 2. Describe which acid (s) you prefer for the application and why. 3. As a result of the use of the reagent you intend to use in the application The time t, where you would assume a total of 20 moles of metal dissolved in real terms as a result, the maximum amount of silver and copper that can be found in solution Calculate the concentrations.
A 0.0200 gram blood sample was decomposed by a microwave digestion technique followed by dilution to 100.0 mL in a volumetric flask. Aliquots of the sample solution were treated with a lead complexing reagent and water as follows: Solution 1: 10.0 ml blood sample + 20.0 mL complexing agent + 30.0 mL H20. Solution 2: 10.0 ml blood sample + 20.0 mL complexing agent + 26.0 mL H20 + 4.00 mL of 78 ppb Pb2+ standard. The resulting solutions were analyzed by UV/Vis at 375 nm. Absorbance for solution 1 = 0.155 and for solution 2 = 0.216. Calculate the concentration of lead (ppb) in the original sample.