A W 16 x 36 is supported by two tension rods AB and CD, as shown in the figure. The 135 KN load is a service live load. Use LRFD and select threaded rods of A36 steel (Fy= 250 MPa and Fu= 400 MPa) if the 135 KN load can be located anywhere between the two rods. Answer _____ A W 16 x 36 is supported by two tension rods AB and CD, as shown in the figure. The 135 KNload is a service live load. Use LRFD and select threaded rods of A36 steel (E= 250 MPa andFu= 400 MPa) if the 135 KN load can be located anywhere between the two rods. AnswerAW 16 × 363m3 m1.5 mk1.5 m135 KN

It is required to determine the factored dead load. The self weight of the beam W16 x 36 is 0.53…

A W 16 x 36 is supported by two tension rods AB and CD, as shown in the figure. The 135 KN load is a service live load. Use LRFD and select threaded rods of A36 steel (E= 250 MPa and Fu= 400 MPa) if the 135 KN load can be located anywhere between the two rods. Answer A W 16 × 36 3m 3 m 1.5 m k1.5 m 135 KN

A W 16 x 36 is supported by two tension rods AB and CD, as shown in the figure. The 135 KN load is a service live load. Use LRFD and select threaded rods of A36 steel (E= 250 MPa and Fu= 400 MPa) if the 135 KN load can be located anywhere between the two rods. Answer A W 16 × 36 3m 3 m 1.5 m k1.5 m 135 KN

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.3P: A plate is used as a bracket and is attached to a column flange, as shown in Figure P8.2-3. Use an...

See similar textbooks

Similar questions

The beam-column in the figure below is a member of a braced frame. A second-order analysis was performed with factored loads and reduced member stiffnesses to obtain the moments and axial force shown. Use LRFDand determine whether this member is adequate. Suppose that P = 165 kFor W10 x 60 with L, = 15 ft and C6 = 1.0: ф,M, = 257 ft-kips, ф,M, = 280 ft-kips;for Lc = 15 ft: cPr = 556 kips.
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. ( Take note: Bottom Distance i need, not the top distance) c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
14 A W8x35 with Fy = 345 MPa is used as a compression member pinned at the bottom, fixed at the top. What should be the maximum length of the member (in m) so that it will not have a possible elastic buckling if rx = 89.15 mm and ry = 51.56 mm . Use theoretical value of k. Write the answer in one decimal place.
A plate is used as a bracket and is attached to a column flange, as shown in Figure P8.2-3. Use an elastic analysis and compute the maximum bolt shear force.
Calculate the service load capacity in tension for an L6x4x1/2 of A36 Grade 36 steel connected with 5/8-inch dia bolts in standard holes as shown in figure 2. The angle tension member is connected to a gusset plate, typical of truss joints. The gusset plate is the plate at the intersection of members to which they are connected. Use American Institute of Steel Construction Load and Resistance Factor Design, and assume the live load to the dead load ratio is 4.0.
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
Q) A simply supported beam with rectangular section shown in the figure below carries a uniformly distributed service dead load of (50 kN/m) (including beam self rated service live load of (80 kN) at mid span, find: 1) Distance fo which the shear reinforcement will be applied. weight) and a conce 2) Spacing required for stirrups ®10mm at critical section. fo=22 Nimm® fy=420 N/mm? 80N +
An unsymmetrical flexural member consists of a ½ x 12 top flange, a ½ x 7 bottom flange, and a 3/8 x 16 web. b.) If A572 Grade 50 is used, what is the plastic moment Mp for the horizontal plastic neutral axis (already answered) QUESTION: SHOW THE SOLUTION FOR GETTING THE y for the top and bottom flange and the web. NOT THE ȳ . and draw the figure for better understanding. SOLVE THE CIRCLED RED PARTS OF THE IMAGE.
1. An unsymmetrical flexural member consists of a 70 × 600 topflange, a 70 x 400 bottom flange, and a 12 × 180 web.a, Determine the Section Modulus.b. Determine the distance from the top of the shape to the horizontalplastic neutral axis.c. If A572 Grade 50 steel is used, what is the plastic moment MPy forthe horizontal plastic neutral axis?
Read the question carefully and give me right solution according to the question. A W12x79 of A573 Grade 60 (Fy=415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at the bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.
The 350×90 section is used as column 10m long. The column is fixed at one end and hinge at the other end. Brace at mid-height about the weak axis (y-axis). W350×90 GIVEN: bf 250mm,d=350mm, Ix=266×10^6mm^4, Iy=44.54×10^6mm^4. Determine the critical effective slenderness ratio of the column. And determine the Pn. Using NSCP 2015.
What size of threaded rod is required for member AB given in figure below. The applied load of X2=181 is the live load and neglect the weight of the member