Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm air enters at 487°C and 105 kPa and the exit temperature of air leaving the chamber is 383.1 K . What is the ratio of the mass flow rates of the cold to hot air streams (m /m,)?

Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm air enters at 487°C and 105 kPa and the exit temperature of air leaving the chamber is 383.1 K . What is the ratio of the mass flow rates of the cold to hot air streams (m /m,)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at a static temperature and pressure of 9°C and 100 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 206 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K)
What is the maximum filtering velocity for chocolate, grains and leather fumes in Pulse-Jet Baghouses?
An aircraft is flying at a cruising speed of 250 m/s at an altitude of 5000 m where the atmospheric pressure is 54.05 kPa and the ambient air temperature is 255.7 K. The ambient air is first decelerated in a diffuser before it enters the compressor. Approximating both the diffuser and the compressor to be isentropic, determine (a) the stagnation pressure at the compressor inlet and (b) the required compressor work per unit mass if the stagnation pressure ratio of the compressor is 8.
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].
The mass flow rate of gas entering nozzle is 25 /m3 . The inlet total pressure= 200kPa and inlet total temperature = 900 K. The exit pressure = 80 kPa ,and isentropic efficiency =92%.Determine the density of gases at the exit and the exit area . (Specific heat is 1100 J/kg.K and gas constant 287 J/kg.K ).
A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
A completely insulated mixing vessel is designed to deliver water at 60 ⁰Cand atmospheric pressure at a rate of 4 kg/s by mixing two streams of incomingwater in an environment at 25 ⁰C. Saturated steam at atmospheric pressure isinserted on the hot side. Two options are being considered for the cold side: (a)chilled water from the plant at 3 ⁰C or (b) water from the tap at 20 ⁰C (both atatmospheric pressure).(i) Determine the mass flow rate of steam and chilled water in each case.(ii) Determine the thermal efficiency of each process.(iii) Determine the exergetic efficiency of each process, defined here as exergy outdivided by exergy in.(iv) Based on the previous answers, discuss which process makes better use ofavailable resources and why.
Air at 90 kPa and 10oC enters an adiabatic diffuser steadily with a velocityof 180 m/s and leaves with a low velocity at a pressure of 100 kPa. Theexit area of the diffuser is 4 times the inlet area. Determine the exittemperature.
Please Help,will provide helpful e Ratings for correct solution. Thank You. Water flows through a horizontal coil through which high-temperature flue gas passes. As water passes through the coil, it passes from the liquid phase at 200 kPa and 80°C to the vapor phase at 100 kPa and 125°C. The entry speed of water into the coil is 3 m/s and the exit speed of steam is 200 m/s. Calculate the heat transferred per unit mass of water through the coil? The enthalpies of the inlet and outlet streams are given as 334.9 kJ/kg and 2726.5 kJ/kg, respectively.
Air flows isentropically through a converging nozzle into a receiver where the absolute pressure is 240 kPa. Air enters the nozzle with negligible velocity, 406 kPa (abs.) of pressure, at a temperature of 95 oC. Determine the mass flow rate through the throat of this nozzle wich area is 0.01 m^2.
Steam enters a turbine at 10,000 kPa and 500 °C, and exhausts at 100 °C with an enthalpy of 2000 kJ/kg. The mass flow rate is m=4.5 kg∙s-1. What is the specific volume (m3/kg) of the exiting stream?
Consider that a flow of air with a velocity of 270 m/s enters an adiabatic diffuser at a pressure of 60 kPa and a temperature of 7°C and exits the diffuser at a pressure of 85 kPa and a temperature of 27°C. Use variable specific heat approach to indicate the air properties. Calculate the ratio of the inlet area to the exit area of the nozzle.