Consider that a flow of air with a velocity of 270 m's enters an adiabatic diffuser at a pressure of 60 kPa and a temperature of 7°C and exits the diffuser at a pressure of 85 kPa and a temperature of 27°C. Use variable specific heat approach to indicate the air properties. Calculate the ratio of the inlet area to the exit area of the nozzle.

Consider that a flow of air with a velocity of 270 m's enters an adiabatic diffuser at a pressure of 60 kPa and a temperature of 7°C and exits the diffuser at a pressure of 85 kPa and a temperature of 27°C. Use variable specific heat approach to indicate the air properties. Calculate the ratio of the inlet area to the exit area of the nozzle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters a turbine at 10,000 kPa and 500 °C, and exhausts at 100 °C with an enthalpy of 2000 kJ/kg. The mass flow rate is m=4.5 kg∙s-1. What is the specific volume (m3/kg) of the exiting stream?
Air at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass ﬂow rate 6 kg/s. The outlet pressure is 100 kPa and assume that speciﬁc heats are constant and evaluated at 600 K. 1. How much power is produced in kW? Round your answer to the nearest whole number. 2. What is the outlet temperature in K? Round your answer to one decimal place.
Air at a static temperature and pressure of 9°C and 100 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 206 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K)
The kinetic energy of a fluid increases as it is accelerated in an adiabatic nozzle. Where does this energy come from? Explain (in brief) using the appropriate equation. An ideal gas enters an adiabatic, horizontal, nozzle (fixed on the ground) at 300 kPa, 200°C and 30 m/s, and leaves at 100 kPa and 180 m/s. These conditions are maintained for all time. The inlet area of the nozzle is 80 cm2. Determine (a) the mass flow rate of gas through the nozzle, (b) the exit temperature ofgas, and (c) the exit (outlet) area of the nozzle. Given: gas constant is 0.287 kPa.m3/(kg.K) ; average value of specific heat capacity of gas (cp, avg) is 1.02 kJ/(kg . ºC)
Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 196 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K), keeping three decimal places.
44#5 air flows steadily at the rate of 0.5 kgm/s through an air compressor, entering at 7m/s speed, 100 kPa pressure and,0.95m^3/kgm specific volume, and leaving at 5m/s,700kPa and 0.19m^3/kgm. the internal energy of the air leaving is 90kj/kgm greater than that of the air entering. cooling water in the compressor jacket absorbs heat from the air at the rate of 58kW. computer the work in kW.
A nozzle is a device that converts fluid thermal energy, enthalpy into kinetic energy. The kinetic energy may be used to drive a mechanical device such as a turbine wheel, thus converting the fluid energy into mechanical work. An adiabatic nozzle receives 0.5 kg/s of air at a pressure of 2700 kPa and a velocity of 30 m/s with an enthalpy of 923.0 kJ/kg; and the air leaves at a pressure of 700 kPa and with an enthalpy of 660.0 kJ/kg. Determine the exit velocity from the nozzle. A closed system containing gas expands slowly in a piston cylinder from 321.7 psf and 8.2 ft3 to a final volume of 19.5 ft3. Determine the work done if the pressure distribution is determined to be P2V2.6 = c. A centrifugal pump operating under steady flow conditions delivers 2,270 kg/min of water from an initial pressure of 82,740 Pa to a final pressure of 275,800 Pa. The diameter of the inlet pipe to the pump is 15.24 cm and the diameter of the discharge pipe is 10.16 cm. What is the work done? A…
A steady flow thermodynamic system receives 100lb/min of fluid at 30psia and 200 °F and discharges it from a point 80 ft above the entrance section at 150 psia and 600°F. The fluid enters with the velocity of 7200 fpm and leaves with the velocity of 2400 fpm. During this process, there are supplied 25,000 BTU/hr of heat from an external source, and the increase in enthalpy is 2.0 BTU/lb. Determine the Work done in horsepower.
Air enters the compressor of a gas-turbine engine at 300 K and 100 kPa, where it is compressed to 700 kPa and 580 K. Heat is transferred to air in the amount of 950 kJ/kg before it enters the turbine. For a turbine efficiency of 86 percent, determine: (a) the fraction of turbine work output used to drive the compressor, (b) the thermal efficiency. Assume: variable specific heats for air.ANS: 52.7% , 27.0%
Steam enters a turbine at 10,000 kPa and 500 °C, and exhausts at 100 °C with an enthalpy of 2000 kJ/kg. The mass flow rate is m=4.5 kg∙s-1. What is the rate of work produced by the turbine?
Air at temperature 27 oC and pressure 66.3 kPa enters the diffuser steadily with a velocity of 190 m/s. The inlet area of the diffuser is 0.6m2. The air leaves the diffuser with nearly zero velocity. Determine the mass flow rate in kg/s of the air. Use R=0.287 kJ/kgK.
Air enters the compressor of a gas turbine plant at ambient conditions of 100 kPa and 25 ⁰Cwith a low velocity and exits at 1 MPa and 347 ⁰C with a velocity of 90 m/s. The compressionprocess is adiabatic, and the power input is 251. Determine the mass flowrateof the air through the compressor please be clear with the writing and explaining