Compressed liquid water at 10 MPa and 20 C enter a steam generator (Heat exchanger) which has auniform 30-mm diameter tube at a rate of 3 L/s. Find the rate of heat added to the water (in kW) if it exists at9 MPa and 400 C.Select oneO a. 8333.8 kWO b. 8638.8 kWO C. 9131.2 kWd. 9556.4 kWO e. 7854.2 kWO f. None of the above

Given Data: The pressure of liquid water at the inlet of the steam generator is, P1=10 MPa. The…

Answered: Compressed liquid

Engineering

Mechanical Engineering

Compressed liquid

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.17P

See similar textbooks

Related questions

Q: Q2/ In an axial flow compresse

Q: The saturated temperature of steam. .with the increase in pressure

A: Saturation temperature and pressure relation is needed to be determined.

Q: vapour pressure.

A: As per guidelines i am allowed to answer first question only.

Q: (c) Do gases usually have a constant specific weight?

A: The specific weight of the gas: The specific weight of the gas is also termed as the specific…

Q: The specific steam

A: Given; Enthalpy at entry and exit is; h1=3159 kJ/kg h2=2187 kJ/kg Specific pump work=2…

Q: Give a concise introduction on Self pressurizing reservoirs

A: Self pressurizing reservoirs :-

Q: Water jet.

A: For solution refer below images.

Q: clearance ratio of the compressor.

A: Given; Clearance volume of a reciprocating compressor, Vc=120 mlVolume of the cylinder at bottom…

Q: specific air consumption

Q: e dryness fraction at low pressure turbine exit (in %)

A: Dryness fraction X=93%

Q: jet

A: α=30oV1=30 m/su=12m/sϕ=18o

Q: Fuel pump __ is a statement of the volume of the fuelflow from the pump.

A: Fuel pump is a device in the vehicle which is used to send the fuel from the tank to the engine…

Q: What is normal air flow rate?

A: Air is the fluid and every fluid has the tendency to flow. when the airflow from the higher pressure…

Q: The day bulb temperature at the exit

A: Given data; Air at atmospheric pressure; Wet bulb temperature, WBT=200C Dry bulb temperature,…

Q: Write the classification of air compressor based on the principle of operation.

A: The four most common sorts of air compressors are: Rotational Screw Compressor. Reciprocating Air…

Q: Multi-evaporator system with individual multiple expansion compressors and valves

A: ME-VCS (multi-evaporator vapour compression systems) are used to cool numerous zones. The…

Q: A pump is being supplied with water from an open tank. The water level of the sOurce

Q: Cold Flid (Water)

A: By using the first law of thermodynamics m˙HOTh2-h1=mCOLD˙h4-h3+QLOSS Here, m˙HOT is the mass flow…

Q: When fluid flows through an orifice, the greater pressure is in the (inlet/outlet) part of the…

A: Concept: Water flow through orifice 1.When the water flow through an orifice (smaller diameter) ,the…

Q: : Specific Heat of Liquids

Q: Condensed pressure cooling system 225 Psi with evaporative pressure 68 Psi Calculate:

A: Given Pressure, P1 = 68 psi = 4.7 bar P2 = 225 psi = 15.5 bar Note: As…

Q: 1. Describe the working principle of Pelton turbine.

Q: For 602.28 kPa Evaporator (8) temperature and degree superheat leaving the compressor (h) mass of…

A: Given data Standard refrigerating cycle withEvaporator pressure = 602.28 kPa ≈ 6 barCondensing…

Q: Describe a cup of hot coffee does not get hotter in a cooler room.

A: According to the law of thermodynamics, the heat is always flows from higher temperature to the…

Q: Apply the steady flow energy equation to nozzle, compressor, turbine, boiler, and mixing chamber.

A: During steady flow-process, the total energy of a control volume remain constant i.e., ECV=constant…

Q: The Pump Work is the work required to push the water into the boiler at a higher pressure

Q: The actual exit temperature

A: Given: Area raio=2.2 Theoretical exit temperature=260 K nozzle efficiency=0.94 To determine: Actual…

Q: thermal efficiency =

A: Need to find thermal efficiency

Q: Name the biogas plant in which the volume of stored gas is not directly visible? Fixed dome type…

A: Given Data→ Biogas plant

Q: erive the speed of sound in

A: given:

Q: = stagnation

A: c) 261.25deg.c

Q: In a venturimeter, the velocity of the liquid at the throat is a. higher than inlet b. minimum c.…

Q: In a double-acting reciprocating pump, the piston carries suction and expulsion does not take place…

Q: 1. Describe the operation of a compressor.

A: A compressor is a mechanical device that increases the pressure of a gas by reducing its volume.…

Q: what is Cp of the air Properties and Compressor

Q: (4) all öf th The refrigerant supplied to a compressor must be (a) superheated vapour refrigerant…

Q: The humidity

A: Given data; Total pressure,p=750 mm of HgPartial pressure,pv=20mm of HgWe have to find teh…

Q: The compressed air supply is intermittent in

A: Answer: (c) Piston compressor

Q: Which statement is correct for a compressed air tank? a) As the temperature decreases, the pressure…

A: if the temperature go below boiling point of air

Q: . As air passes through an axial flow compressor, a pressure rise takes place in: The stator vanes…

A: Ans: Option C is correct. Both the rotor blades and stator vanes

Q: Which temperature for lubricating oil will be lowest? 1) Flash point 3) Pour point 2) Fire point 4)…

A: Pour point A point for a liquid at which its flowing property changes and becomes semisolid in…

Q: The volume of air delivered by the compressor is called A) Compressor capacity B) Swept volume C)…

A: Given Data⇒ Volume of air delivered by the compressor Problem statement⇒ The volume of air delivered…

Q: The total pressure rise in a centrifugal compressor is due to impeller and diffuser action Select…

A: The fluid flowing through the impeller of the centrifugal compressors are imparted kinetic energy…

Q: mass flow rate of the liquid

A: Given data; Blade outer radius,r=50 mm It consumes power,P= kWN= 3000 rpm Determine mass flow rate…

Q: turbine

A: To find ; Number of revolutions of a wind turbine.

Q: velocity and discharge.

Q: The fractions of solid and liquid

A: Given data; Binary phase diagram of metals P and Q is shown in figure. Alloy containing 60% P 40%…

Q: * :Water vapor in the ambient air usually saturated vapor saturated dry vapor superheated vapor…

A: The ambient air has various types of gases such as oxygen, nitrogen, Carbon Dioxide, Water Vapor and…

Q: The percentage by volume of oxygen in ..atmospheric air is nearly

A: GIVEN DATA AN MCQ IS GIVEN ASKING % BY VOLUME OF OXYGEN IN ATMOSPHERE WE HAVE TO CHOOSE CORRECT…

Q: air pressure above the liquid A in bars.

A: Given: l1=3.65 m l2=1.25 m l3=1.25 m h1=1.15 m h2=0.85 m SgA=1.2 SgB=1.0 SgC=0.85 SgA=1.2 To…

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

Compressed liquid water at 10 MPa and 20 C enter a steam generator (Heat exchanger) which has a
uniform 30-mm diameter tube at a rate of 3 L/s. Find the rate of heat added to the water (in kW) if it exists at
9 MPa and 400 C.
Select one
O a. 8333.8 kW
O b. 8638.8 kW
O C. 9131.2 kW
d. 9556.4 kW
O e. 7854.2 kW
O f. None of the above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.
water at 366 k is transfer from storge tank to another at rate 50 m3/min .The pump supplied work at rate 2 kJ , this water pass through heat exchanger ,which give heat about 40000 kJ/min .This water delivered to second tank at distance 300 cm above the first tank. What the temperature in second tank ?
Steam flows through a turbine at the rate of 100 lb/min with ∆KE = 0 and Q = 0. At entry, its pressure is 175 psia, its volume is 3.16 ft3/lb, and its internal energy is 1166.7 Btu/lb. At exit, its pressure is 0.813 psia, its volume is 328 ft3/lb, and its internal energy is 854.6 Btu/lb. What horsepower is developed? (b) The same as (a) except that the heat loss from the turbine is 10 Btu/lb of steam.
A 6cm inlet valve and a 3cm exhaust valve in a turbocharged engine, assume both valves have a discharge coefficient of 0.7 and a lift of 8mm. Find the mass flow rate (in kg/s) at IVO if the cylinder pressure is 115kPa, the inlet manifold pressure is 140kPa, and the manifold air temperature is 310K.
The oil (cp = 1 795 W-s/kg-K) from an oil-cooled electric transformer is cooled from 79.4 oC to 29.4 oC at the rate of 1 360.5 kg/h. This is done in an oil-water het exchanger that receives 2 948 kg/h of water at 15.6 Celsius. For the exchanger, U = 295 W/m2-K. Find the exit water temperature and heating area required (a) for counter flow and (b) for parallel flow.
Find the mass flow rate in lbm/s of a liquid (p=0.69 g/cm³) flowing through a 5 cm (inside diameter) pipe at 8.3 m/s.
Air is compressed in a two-stage , double-acting compressor which is electrically driven at 165 rpm. The low pressure cylinder (30.5 x 35.5-cm) receives 6.85 m3/min of air at 96.53 kPaa, 43.3°C, and the high pressure cylinder (20.3 x 35.5-cm) discharges the air at 717.06 kPa. Piston rods are 5.1 cm in diameter and the isothermal overall efficiency is 74%. Find (a) the volumetric efficiency, (b) the power of the driving motor.
can you please solve this for me, thanks. 10 kg/s of steam (H2O) enters a turbine at 10 m/s and a specific enthalpy of 3500 kJ/kg and leaves at an outlet 10m below the inlet with a specific enthalpy of 2500 kJ/kg and a velocity of 20 m/s. Assume steady-state steady-flow. If the heat lost from the turbine is 20% that of the turbine work, determine a.) the turbine horsepower. If the turbine is coupled to a generator with a 90% electrical efficiency, and the turbine horsepower has an 80% mechanical efficiency, b.) how much income will a power plant generate in one year if the electrical energy is sold at PhP 3.51 per kW-hr? (Hint: Mechanical efficiency = actual turbine work / ideal turbine work. Electrical efficiency of a generator = electrical output / actual turbine work.)
Air is compressed in a two-stage , double-acting compressor which is electrically driven at 165 rpm. The low pressure cylinder (30.5 x 35.5-cm) receives 6.85 m3/min of air at 96.53 kPa, 43.3°C, and the high pressure cylinder (20.3 x 35.5-cm) discharges the air at 717.06 kPa. Piston rods are 5.1 cm in diameter and the isothermal overall efficiency is 74%. Find (a) the volumetric efficiency, (b) the power of the driving motor.
single row impulse turbine receive 3 kg/s of steam with velocity 425 m/s . The blade speed ratio is 0.4 and the output power is 171.58 kW. If the frictional losses in the moving blade amount to 14.92 kW, determine the diagram efficiency and the blade velocity coefficient. The nozzles angle is 16o
In a nozzle, steam enters at T = 673.15 K and P = 800,000 Pa while u = 15m/s. It exits at T = 400,000 Pa and u = 320m/s. What is the ration of the inlet and outlet diameters (D1/D2)?
Air enters a blower at 20°C and exits at 28.38°C. The inlet velocities of air are 100 m/s and 150 m/s respectively. Find the mass flow rate if the blower consumes a power of 15 kW, assuming adiabaticconditions. Take cp of air is 1.005 kJ/kg-K. Need answers and solutions. ASAP...