An idealized centrifugal pump (blade outer radius of 50 mm) consumes 2 kW power whilerunning at 3000 rpm. The entry of the liquid into the pump is axial and exit from the pump isradial with respect to impeller. If the losses are neglected, then the mass flow rate of the liquidthrough the pump is

Given data; Blade outer radius,r=50 mm It consumes power,P= kWN= 3000 rpm Determine mass flow rate…

Answered: mass flow rate of the liquid

Engineering

Mechanical Engineering

mass flow rate of the liquid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 10∙1 A rectangular plate 0.5 m long, 0.25 m wide and 10 mm thick is simply supported at the edges.…

Q: Given 3 + 5y² = sinx, y(0.3) = 5 and using a step size of h = 0.3, what is the value of y(0.9)?

Q: Find the strain Initial length=102.78 mm Change in length=0.004 mm

Q: 6/3 The designer of a ski resort wishes to have a portion of a beginner's slope on which the skier's…

A: To calculate angle for constant velocity, we equate net force equal to zero in sliding direction.…

Q: PROBLEM 2 The two steel shafts are connected by gears D and C. Shaft AC is 4.0in in diameter while…

Q: Q2(30%) Determine the resultant of forces system shown in Figure and locate it with respect to point…

A: Given Force, F1 = 380 kN F2 = 20 kN F3 = 30 kN F4 = 80 kN Find…

Q: ꜰɪɴᴅ ᴛʜᴇ ᴀɪʀ ʜᴏʀꜱᴇᴘᴏᴡᴇʀ ɪꜰ ᴀɴ ɪɴᴅᴜꜱᴛʀɪᴀʟ ꜰᴀɴ ᴛʜᴀᴛ ᴅᴇʟɪᴠᴇʀꜱ 25.98 ᴍ3/ꜱ ᴏꜰ ᴀɪʀ ᴛʜʀᴏᴜɢʜ ᴀ 0.915 ᴍᴍ x…

Q: Find the strain Stress=35.87 MPa E=65 MPa

A: Given data : Modulus of elasticity=E Stress=σ Required : Strain

Q: Fnd the potential energy m = 33kg h = 10m g=lomis2

Q: 4/16 The rectangular frame is composed of four perim- eter two-force members and two cables AC and…

Q: 4. An ideal diesel cycle has a compression ratio of 20 and a cutoff ratio of 1.3. Determine the…

Q: For the two-dimensional case shown in Figure P6.15, where y = 1.4, determine M3 and p3- 5° P₁ = 10…

Q: The average velocity in a pipe flowing full of incompressible liquid is 3 m/s. after passing through…

A: Given Initial velocity, v1 = 3 m/s Initial area = A1 Final area, A2 = A1/4…

Q: A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and…

Q: ᴀ ᴄᴇɴᴛʀɪꜰᴜɢᴀʟ ᴘᴜᴍᴘ ᴡɪᴛʜ 76ᴍᴍ ᴅɪᴀᴍᴇᴛᴇʀ ɪᴍᴘᴇʟʟᴇʀ ᴅᴇʟɪᴠᴇʀꜱ 38ʟ/ꜱ ᴏꜰ ᴡᴀᴛᴇʀ ᴀɢᴀɪɴᴛꜱ ᴀ ᴛᴏᴛᴀʟ ʜᴇᴀᴅ ᴏꜰ 107ᴍ…

Q: The braking torque on the drum is

A: Given data; External drum brake is shown in figure. Diameter,d= 500 mm Dimensions of the brake…

Q: 107. A body moves, from rest with a constant acceleration of 5 m per sec. The distance covered in 5…

A: Given data : Acceleration=a Time=t Initial velocity=U Required : Distance

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: Crude oil, Cp = 1.9 kJ/(kg.K), flows at a rate of 0.32 kg/s through the inner pipe of a tube-in-tube…

Q: HOME WORK 1. Calculate the maximum and minimum limits for both the shaft and hole in the following;…

Q: Consider the right-handed coordinate system below. The force F = 800 N has its line of action…

Q: 4ft R₁ 7ft 3P 7ft 4ft 2in k4in 8in 2in

A: Given

Q: A = - rolled steel channel (Ix 8.87 x 106 mm², I₂ = 40.3 × 10¹ mm²) is used as a simply supported…

A: In a roof truss, we know that a rolled steel channel is employed as a simply supported beam.We must…

Q: Carnot heat engine receives heat at 750k and rejects the waste heat to the environment at 300k .the…

Q: 7.15 Two left-hand helical gears having the same helix angle are used to connect two shafts 60°…

A: (a) The number of teeth on gear: ZG = 62 teeth (b) The number of teeth on pinion: ZP = 25 teeth

Q: Air standard dual cycle: description of the processes, p-v and T-s diagrams

Q: Find the value of stress Force 2.2 N Area=2 m2

A: Given data : Area is denoted by A Force is denoted by F Required : Stress

Q: Using the relations among load, shear and moment, draw shear and moment diagrams, specifiying the…

A: The section is as shown below,

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: 6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: 150 N 35⁰ y e 120 N 30⁰ 40⁰ 80 N

Q: A gas tungsten arc welding operation is performed using a current 140 A and arc voltage of 15 V at a…

Q: . The given force F = 9 kN is to be resolved into its components along axis OA and OB. What is the…

Q: 12 rad/s P Å R 110 mm C 110 mm 65 mm 85 mm Members PQ and QR are joined by a hinge at Q. End P of…

Q: Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8…

A: Given Diameter, D = 15 cm d = 8 cm Flow rate, Q = 0.035 m3/s Find Head loss, h

Q: The fractions of solid and liquid

A: Given data; Binary phase diagram of metals P and Q is shown in figure. Alloy containing 60% P 40%…

Q: Which of the following equations below describes the system head of the piping shown below. The…

Q: an automatic door mechanism where when a specific sensor on top detects a user approaching, where…

A: Draw the flow chart.

Q: Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C.…

Q: For a mixture of 40% nitrogen, 35% oxygen, and 25% carbon dioxide on a molar basis, what is the…

A: Given data P=RTv-b-avv+bT1/2a=?N2=40%CO2=25%O2=35%

Q: Find hydraulic radius Wetted area=5 m2 Wetted perimeter-7

Q: A |100 16 B +20+4t | 80 16 - 30┫

Q: Q3) Water at 4°C enters a tank of diameter D₁ = 50 cm at a constant mass flow rate of min= 1kg/s. An…

Q: A 360° journal bearing is 3 in. long and carries a 4 in. diameter shaft with a radial clearance of…

Q: A person with a body mass of m= 99 kg and height h = 1.74 m stands with their arms straight out.

A: Mass, m=99 kg,Height, h =1.74 m,

Q: H.W4 Determine the slope of the simply supported beam at A and deflection at C. E = 200 GPa and I =…

A: Given Load, W = 20 kN Moment, M = 10 kN.m Length, L = 6 m E = 200 GPa Find…

Q: What is the flow rate of a horizontal rectangular system when the conditions are as follows:…

A: GivenA=9ft2L=9ftPi=7atmPo=4atmμ=1cpk=1 darcy

Q: the net heat input per unit length of the weld.

A: Given data; Determine the net heat input per unit length of the weld ? Current,c= 450 A…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

A: There will be three reactions induced at the supports i.e., 2 at the hinged support(A) and 1 at the…

Q: A motorboat and its load weigh 980 kg. Assume that the propeller force is constant and equal to 24…

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

An idealized centrifugal pump (blade outer radius of 50 mm) consumes 2 kW power while
running at 3000 rpm. The entry of the liquid into the pump is axial and exit from the pump is
radial with respect to impeller. If the losses are neglected, then the mass flow rate of the liquid
through the pump is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A centrifugal pump delivers 0.071 m3/s of water against a head of 7.6-m at 1450 rpm and requires 6.7 kW. If the speed is reduced to 1200 rpm calculate the head, assuming the same efficiency.
The fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rpm with the 1/4 ratio model of a centrifugal pump designed to be used for oil. Calculate the power given by the pump to the fluid when the prototype pump operates at 1000 rpm. (ρsu = 1000 kg / m3, ρ oil = 800 kg / m3)
A centrifugal pump with radial inlet (alpha4 = 90°) operates with water at a flow of 0.3 m3 /s. The rotor diameter is 250 mm and the blades it is 30 mm wide at the outlet. Assume that the blades are radial at the exit. Determine the theoretical height considering infinite number of blades and power required when the pump runs at 800 rpm.
Consider a centrifugal pump with curved blades has blade angle at the outlet section equal to 30o, and no shock/no swirl at inlet. Construct the velocity diagrams of this blade at inlet and outlet sections.
A centrifugal pump discharges 96L/s while running at 1380rpm against a net head of 14m. The manometric efficiency of the pump is 0.92. If the vane angle at the outlet is 35 deg, estimate the outer diameter of the impeller and its width at that diameter. Assume the velocity of flow.
A centrifugal pump with impeller diameter 500mm is designed for a discharge of 1.0m3/s of water. The water enters the pump axially, leaving the impeller with an absolute velocity of 12m/s at an angle of 20degrees to the tangent at the impeller periphery. The impeller is rotating at 700rpm. Determine the exit vane angle and the hydraulic power delivered.
A centrifugal pump outer diameter equal to two times the inner diameter and running at 1200 rpm works against a total head of 75 m the velocity of the flow through the impeller is constant and equal to 3 m/s. The vane are set back at an angle of 30° at outlet. If the outer diameter of the impeller is 600 mm and width at out let is 50 mm, determine; 1- Vane angle at inlet. 2- Work done per second by imepller.
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
A plant has installed a single-suction centrifugal pump with a capacity of 300gpm under 200ft at 1200rpm. It is proposed to install another pump with double suction but of the same type to operate at 100ft head and delivers 400gpm. Determine the speed of the proposed pump.
A centrifugal pump runs at 1750 rpm while pumping water at a rate of 50L/s. The water enters axially, and leaves tangential to the impeller blades. The impeller exit diameter and width are 150 mm and 10 mm, respectively. If pump requires 45 kW, and its 75% efficient, estimate the exit angle of the impeller blades.
Provide the neccesary equations in designing a centrifugal compressor such as the dimensions for impeller. What are the initial given values?
A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The head developed is 72.8 m. The width of the impeller at outlet is 0.22 m. If the overall efficiency is 91.7% determine the power to drive the pump.