concentration of the total suspended solid. In the laboratory, 5 mL of the water sample was ransferred to a 100 mL volumetric flask before diluted with distilled water to 100 mL. After that, 50 mL of the diluted water sample was transferred to a funnel containing a glass fiber filter and attached to a glass flask with the sidearm connected to a operating vacuum pump. Transferred diluted water sample was left drained through the glass filter before glass fiber was transferred to an oven to heat at 105 oC under a constant weight of 0.2654 g was obtained. If the initial weight of the glass fiber filter is 0.2431 g. Calculate the amount of the suspended solid in mg unit contained

concentration of the total suspended solid. In the laboratory, 5 mL of the water sample was ransferred to a 100 mL volumetric flask before diluted with distilled water to 100 mL. After that, 50 mL of the diluted water sample was transferred to a funnel containing a glass fiber filter and attached to a glass flask with the sidearm connected to a operating vacuum pump. Transferred diluted water sample was left drained through the glass filter before glass fiber was transferred to an oven to heat at 105 oC under a constant weight of 0.2654 g was obtained. If the initial weight of the glass fiber filter is 0.2431 g. Calculate the amount of the suspended solid in mg unit contained

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.19QAP

See similar textbooks

Similar questions

Patients undergoing an upper gastrointestinal tract laboratory test are typically given an X-ray contrast agent that aids with the radiologic imaging of the anatomy. One such contrast agent is sodium diatrizoate, a nonvolatile water-soluble compound. A 0.378-m solution is prepared by dissolving 38.4 g sodium diatrizoate (NaDTZ) in.l.60 102 mL water at 3 1.2C (the density of water at 31.2C is 0.995 g/cm3). What is the molar mass of sodium diatrizoate? What is the vapor pressure of this solution if the vapor pressure of pure water at 31.2C is 34.1 torr?
A concentration of toxic metals in plant tissue is often found by combusting the material in a furnace and then dissolving the ash in concentrated acid. A 0.5124-gram sample of leaves was combusted to ash and transferred to a 150-mL beaker. A 25-mL portion of concentrated HCl was added and the mixture was heated on a hot plate. Three 5-mL portions of concentration HCl were added over approximately 10 minutes with continued heating in between additions. The resulting mixture was cooled to room temperature and filtered into a 50-mL volumetric flask, which was brought to volume using distilled water and mixed well. From this stock solution, a 10-mL portion was pipetted into a clean 50-mL volumetric flask, brought to volume with distilled water, and mixed. This final solution was analyzed and found to contain 12.1 ppm lead. What are the mass percent of lead in the original plant tissue?
A pipet is used to transfer 6.00 mLmL of a 3.75 MM stock solution in flask “S” to a 25.00-mL volumetric flask “A,” which is then diluted with DI H2OH2O to the calibration mark. The solution is thoroughly mixed. Next, 10.00 mLmL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2OH2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask “S” to a 25.00-mL volumetric flask “B,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 3.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
. The total cation content of natural water is often determined by exchanging the cations for hydrogen ions on an ion exchange resin. The cations are adsorbed to the resin which releases H+ (1:1 exchange) which can then be titrated with a base. A 25.0 mL sample of a natural water is diluted to 100 mL with distilled water and 2.0 g of a cation-exchange resin was added. After stirring, the mixture was filtered and the solid remaining on the filter paper was washed with three 15.0 mL portions of distilled water. The filtrate and washing required 15.3 mL of 0.0202 M NaOH to reach the equivalence pt. Calculate the number of moles of cation present in 1.00 L of sample.
A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask “S” to a 25.00-mL volumetric flask “A,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 2.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
By pipet, 15.00ml of the stock solution of potassium permanganate (KMn04) that was prepared by dissolving 13.0g KMn04 with DI H20 in a 100.00ml volumetric flask, diluting to the calibration mark was then transferred to a 50.00ml volumetric flask and diluted to the calibration mark. Determine the molarity of the resulting solution.
A 532 mg of a mixture of fluorene and benzoic acid was weighed out and subjected to an extraction and recrystallization. After this purification was completed the product crystals were dried and analyzed. The purification procedure produced 174 mg of fluorene and 249 mg of benzoic acid. Calculate the percent composition of this mixture.
Six 50.0 ml volumetric flask 1 through 6 are labeled. 10.00 ml of 2.00 x 10-1 M Fe(NO3)3 solution was then pipet into each volumetric flask. A 1.00,2.00,3.00,4.00 and 5.00ml of 2.00 x 10-3M NaSCN solution was then pipetted to flask 2 through 6 respectively. A sufficient amount of 0.10 M nitric acid was then added to each flask to make each a total volume of 50.00ml. Hint M1V1=M2V2 a)what would be the concentration of Fe(NO3)3 in 0.10M HNO3? b)what would be the concentration of NaSCN in 0.10M HNO3?
A spent 1.0 percent caustic soda solution (ρNaOH = 8.42 lb/gal) with a volumetric flow rate of 3.0gpm is to be neutralized using either sulfuric acid or hydrochloric acid. First, determine the massflow rate (lb/day) of NaOH in the spent caustic soda solution, and then use that value todetermine the stoichiometric amounts (lb/day) of:1. H2SO4 required for neutralizing the OH− ions contributed by the spent caustic soda.[Hints: (1) write the balanced chemical equation for the acid-base reaction betweenNaOH and H2SO4, and use it to establish the stoichiometric weight ratio H2SO4 : NaOH.]2. HCl required for neutralizing the OH− ions contributed by the spent caustic soda. [Hints:(1) write the balanced chemical equation for the acid-base reaction between NaOH andHCl and use it to establish the stoichiometric weight ratio HCl : NaOH.]
If you mixed a solution at ARCC that was 17.5 % mass/mass of the sugar sodium and then transferred 2.00 mL weighing 3.21 g into a graduated cylinder and diluted to 10.00 mL, what mass of sodium was transferred to your new solution?
A core sample is saturated with an oil (?o = 35oAPI), gas and water. The initial weight of the sample is 224.14 g. After the gas is displaced by water (?w = 1 g/cm3 ), the weight is increased to 225.90 g. The sample is the placed in a Soxhlet distillation apparatus, and 4.4 cm3 water is extracted. After drying the core sample, the weight is now 209.75 g. The sample bulk volume, 95 cm3 is measured in a mercury pycnometer. Find the porosity, water saturation, oil saturation, gas saturation and lithology of the core sample.