A room window measure (3 m²) constructed of glass with overall heat transfer coefficient of (4 W/m?. °C). The inside design condition of room is ( 22 °C dbt and 50% RH) while the outside temp equals -7 °C. Determine; a) The inside glass surface temp b) Will moister condense on this window c) Select different glass type to prevent the vapoure condense over glass

A room window measure (3 m²) constructed of glass with overall heat transfer coefficient of (4 W/m?. °C). The inside design condition of room is ( 22 °C dbt and 50% RH) while the outside temp equals -7 °C. Determine; a) The inside glass surface temp b) Will moister condense on this window c) Select different glass type to prevent the vapoure condense over glass

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.17P

See similar textbooks

Similar questions

Q2 : Room walls are composed of common bricks and outside and inside plaster layers with an overall heat transfer coefficient of 2.5 W / m² ° C . The outside air temperature is 15 ° C ( DBT ) and the inside design conditions are 23 ° C DBT , 55 % RH . Is condensation occur on the inside surface or not ? Take f = 8.26 W / m² ° C . SHI
In a reservoir system with a very large accumulation volume for the ideal fluid (water),a) Since the diameter of the ABCDEF outlet pipe is D = 20 cm, the flow rate through the pipe,b) Calculate the velocity, velocity height, relative pressure and pressure heights in the ABCDEF outlet pipe.c) Draw the relative energy and piezometer lines of the system.d) If the relative evaporation pressure of water is pv = -98.5 kPa, what can be z maximum?e) Determine how much the diameter of the outlet pipe can be reduced at most without causing cavitation, with the relative evaporation pressure of water pv = -98.5 Pa and h = 6 m.f) Calculate the critical velocity value for cavitation.
An air-cooled condenser has an expected h value of 30 W/m2-K based on the air-side area. The condenser is to transfer 60kW with an airflow rate of 15kg/s entering at 35C. Take the condensing temperature is to be 48C What is the exit temperature of cooling air? . Group of answer choices 34.94 degC 36.96 degC 30.90 degC 38.98 degC
Only answer if you are 100% sure otherwise i will downvote... An ASTM B75 copper tube sheathes a heating element that is used to boil water at 1254 kPa. The copper tube is immersed horizontally in the water, and its surface is polished. The tube diameter and length are 5 mm and 9.5 cm, respectively. The maximum use temperature for ASTM B75 copper tube is 204°C. Determine the highest evaporation rate of water that can be achieved by the heater without heating the tube surface above the maximum use temperature. Use the property tables to calculate the properties of water at saturation temperature. The surface tension 0 at 190°C is 0.03995 N/m. Also, Csf 0.0130 and 10 for the boiling water on a polished copper surface. The highest evaporation rate of water is g/s?
In a steam boiler with a volume of 2 m3, there is wet water vapor at 200 kPa pressure. Since it is known that 20% of the volume of the boiler is water and 80% is steam,a) The temperature of the wet water vaporb) degree of drynessc) Specific volume
Q2.1 Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate?
An electric current is passed through a wire 1 mm in diameter and 10cm long. The wire is submerged in liquid water at atmosphericpressure, and the current is increased until the water boils. For thissituation h=5000W/m2◦C, and the water temperature will be 100◦C. How much electric power must be supplied to the wire to maintain the wire surface at 114◦C?
The critical temperature of gas TOS is -46 deg Celsius. If the value of its Van der Waals constant b is 2.1 x 10 -5 m3/n, find the value of its VDW constant a in Pa-m6/n2
Explain the P-v-T surface of a substance that expands on freezing (like water).
Consider a tank with surface area A.(m2) It containsa fluid of M(kg) at an initial temperature of T0. (C) The specific heat of the fluid is Cp. (J/kg) The fluid inside the tank is heated with condensing vapour outside at temperature of Ts. find the equation that gives the change of the temperature of the fluid in the tank with time.T=f(t) neglect donduction heat transfer h=heat transfer film coef. homogenous T through the tank
What is the temparature at depth 1 cm from the surface at t=2 minutes after the start of the coolıng ?
A shell-and-tube condenser with horizontal 7/8-in BWG 16 copper tubes is used to condense benzene vapor. The vapor is condensed at atmospheric pressure, it’s enthalpy of vaporization is around 394 KJ/kg, and the thermal conductivity at the reference temperature is around 0.150 W/m.°C. Assume the cooling water average temperature to be 40°C and neglect the tube and water film resistances. a)Calculate the reference temperature Tf and evaluate the liquid properties at this temperature. You may use the textbook and/or Perry’s Chemical Engineers’ Handbook. b)Estimate the film coefficient for the top row of tubes (W/m2.°C). c)Estimate the average coefficient for a stack of 10 tubes (W/m2.°C).