Consider a hollow drainage concrete cylinderof uniform mass density of 2,400 kg/m³ withlengthL= 60m with R1 of 2.8 m .Find its outerradius (R2) in m if the moment of Inertia is5,067,000 kg-m? about its axis of symmetry is

Answered: Image /qna-images/answer/cc9e85d6-426b-46c8-aafc-94d306de9478.jpg

Consider a hollow drainage concrete cylinder of uniform mass density of 2,400 kg/m with lengthL= 60m with R1 of 2.8 m .Find its outer radius (R2) in m if the moment of Inertia is 5,067,000 kg-m about its axis of symmetry is

Consider a hollow drainage concrete cylinder of uniform mass density of 2,400 kg/m with lengthL= 60m with R1 of 2.8 m .Find its outer radius (R2) in m if the moment of Inertia is 5,067,000 kg-m about its axis of symmetry is

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Related questions

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: The given data is: Dimensions of sluice gate are: Breadth (B) = 8 m Depth (d) = 6 m Oil Density…

Q: What will be the pressure head of a point in mm of Hg if pressure head of that point is equal to 63…

A: In this question head is given in terms of water and that head is equal to 63 CM We are asked to…

Q: Would a wooden cylinder (sp. gr. = 0.61) 660 mm in diameter and 1.3 m long be stable if placed…

A: Given: The diameter of the cylinder is 660 mm. The length of the cylinder is 1.3 m. The specific…

Q: The hydraulic dredge shown in the figure below is used to dredge sand from a river bottom. Estimate…

A: Fluid is an important part of the fluid mechanic's sector. Liquids can compress or misalign three…

Q: Question 16 The pipe diameter is 800mm. The ultrasonic measurements recorded are: • Pipe centerline…

Q: Determine the pressure required to reduce the given volume of water by 1 % (Bulk modulus or…

A: Given data in question Bulk modulus 2×108 N/m2 Reduction volume ratio 1% = 0.01 To find out…

Q: Q1: Figure shows the water pipe network shown: a) Analyze the water pipe network shown take…

Q: 8. Calculate the hydrostatic pressure for water moving with constant velocity at a depth of 5 m from…

A: Fluid mechanics is the discipline of physics that studies the mechanics of fluids (liquids, gases,…

Q: ly ôf 3.5 m/s through a circular pipe, knowing that the flow is laminar with a friction factor…

Q: Estimate the height to which water will rise in a capillary tube of diameter 4mm of the surface…

A: Given data in question Surface tension Diameter Water Angle of contact To find out Height of…

Q: The discharge (Q) through a horizontal pipe is depend upon the pressure drop per unit length(AP) the…

Q: If a concrete cube 300 mm on a side is to be fully submerged in a liquid having a specific gravity…

A: Given Data:side = 300mmspecific gravity of liquid = 4.70specific gravity of concrete = 2.35

Q: Example 6.1. In a pipe of 90 mm diameter water is flowing with a mean velocity of 2 m/s and at a…

A: To find the total Head -

Q: A Pitot tube having a coefficient of Cy = 0.98 is used to measure the velocity of water at the…

Q: For the figure shown below, find the equivalent permeability of the system if. K2=3K1: K3=2K1;…

Q: 1. Calculate the water pressure acting on the vertical walls of a concrete structure. P Ly1=5 M…

Q: velocity (ft/s) at point 1, velocity (ft/s) at point 2, and pressure head (ft) at 2. e pressure head…

A: Q=A1v1=A2v213.2=π412×v1=π422×v2v1=13.2π412=16.8067ftsv2=13.2π422=4.2016fts

Q: 2. By what factor will the hydrostatic force on one of the vertical sides of a beaker decrease if…

A: To determine by what factor the hydrostatic force on the vertical face of a beaker decrease upon…

Q: The submerged sector gate AB shown in the figure is 1/6 of a circle of radius 4 m. The length of the…

A: Given Data: Length of gate is L=10 m. Height of gate is H H=4 mtan60°=4×0.866=3.464 m

Q: 4 Calculate the whirling speed of a shaft 20 mm diameter and 0.6 m long carrying a mass of 1 kg at…

Q: What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.05 N/cm²…

A: Given data- Pressure inside water droplet-P=0.05 N/cm2Surface tensionσ=0.075 N/mTo Find-Diameter of…

Q: A cylinder of cross- sectional area 3500 mm is filled with sand of Overfow permeability 6 mm/s.…

A: Solution Given Data Cross-sectional area= 3500 mm2 Permeability= 6 mm/s

Q: A pipe has a length of 447 meters. Water is flowing in the pipe at a rate of 0.53 m3/s. If the…

Q: A solid cone of diameter 24 cm and height 20 cm floats with its vertex downwards in water as shown…

Q: A certain part of cast iron piping of a water distribution system involves a parallel section. Both…

A: We have to determine the flow rate through pipe B by assuming the flow is fully rough, thus the…

Q: A vertical water jet is issuing upwards from a nozzle with a velocity of 10 m/s. The nozzle exit…

Q: The figure shows a cylinder of 4 m dlameter in equilibrium. Calculate the vertical component of…

Q: 8) Estimate the height to which water will rise in a capillary tube of diameter 3mm. Use o =0.0728…

Q: Q.1 For the concrete dam shown in figure, square I is (1.5x1.5m). Find: 1. value of hị and h; if (i)…

Q: 5. A liquid jet of 5 cm diameter has a pressure difference of N/m?. (Take surface tension as 0.075…

Q: Figure P8.19 shows a pipeline through which water flows at a rate of 0.06 m3/s. The pipe is 3000 m…

A: The given figure is shown below:

Q: PROBLEM 2 . A tank is in the shape of a frustum of a pyramid having a square section .The upper base…

Q: Example 3: Investigate the stability of a wooden beam, 0.20 m x 0.30m x 10m in dimensions. The beam…

Q: Consider flow in a 350mm diameter steel that is coated with a very smooth enamel. Water flows in it…

A: The energy expended in a fluid system owing to friction throughout the length of a pipe or hydraulic…

Q: The pipe diameter is 800mm. The ultrasonic measurements recorded are: Pipe centerline velocity = 4.9…

Q: Q4- For the apparatus shown in the Figure below, a) Determine the pressure, elevation, and total…

Q: Try to solving these problems: 1. Water at A has a pressure of 400 kPa and a velocity of 3 m/s.…

A: PB= 381.718 Kpa VB= 6.75 m/sec Pc= 40 Kpa Vc= 27 m/sec

Q: 1. Determine the discharge through the sand layer in ft/min. The total length of the dam is 3000 ft.…

A: Given data, Length of dam = 3000 ft T = 20 ft B = 240 ft K = 0.05 ft/minutes. To find out the…

Q: Determine the following: a. Enclosed Area Given is a thin-walled tube with the following data: Wall…

A: Angle of twist The angular distortion in an item caused by a couple of twisting torques is known as…

Q: 11- In an infinite two-dimensional flow filed, a sink of strength 3/2n m/s.m is located at the…

A: The given data is as follows: Strength of sink located at origin=32πm3/s.mStrength of another sink…

Q: A piezometer and a Pitot tube are tapped into a 4-cm diameter horizontal water pipe, and the height…

A: Velocity at the center of pipe (V) : V =2gh h is the height of the water columns g is the…

Q: Water flows at 2 m / s in a 3 m wide 2.5 m deep rectangular channel. There is a 1.10 m elevation on…

A: Velocity of the flow = v = 2m/s Width = b1 = 3m Depth at 1st section = y1 = 2.5m △z = 1.10my2 =…

Q: 2. A beaker is filled with a liquid of specific gravity S = 1:2 as shown. What will be the pressure…

Q: Problem 3. The strength per meter of the longitudinal joint in the figure is 480 KN whereas the…

Q: If the velocity profile of a fluid over a plate is parabolic with free stream velocity of 120 cm/sec…

A: u = 120cmsec y = 20cm μ = 8.5poiseORμ = .85N-sm2

Q: Consider the lifting flow over a circular cylinder. The lift coefficient is 5. Calculate the peak…

A: Solution Lift coefficient= 5

Q: The submerged sector gate AB shown in the figure is 1/5 of a circle of radius 4 m. The length of the…

A: Solution Given Data The length of the gate= 10 m Radius= 4 m

Q: A point load P is applied at point A on the ground surface as shown on the figure. Using Wastergards…

Q: A tank 12 m high is to be filled with oil with unit weight of 9.4 kN/m³ as shown in the figure.…

Q: 4 pts In the dam figure with assumed 1 meter strip: water depth D=9m, dam height H=12m, and dam base…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Consider a hollow drainage concrete cylinder
of uniform mass density of 2,400 kg/m³ with
lengthL= 60m with R1 of 2.8 m .Find its outer
radius (R2) in m if the moment of Inertia is
5,067,000 kg-m? about its axis of symmetry is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A conical tank is inclined with an angle of 60°. A hole with radius 2-in was opened at the bottom. If initially the tank is full to a height of 9 ft, how long will the tank drain? Consider a coefficient of contraction, 0.6.
A cylindrical tank 2m in diameter and 15 meters high is filled with liquid Z. A pressure gage at elev 10 m at the side of the tank reads 105 kPa. another gage at elev 6m reads 138 kPa. compute the (a) specific weight of the liquid and (b) density of the liquid.
This is a mercury U-tube*acceleration = 4.905 m/s^2 to the right What is the gage pressure at A? in kPa
Water flows at 2 m / s in a 3 m wide 2.5 m deep rectangular channel. There is a 1.10 m elevation on the downstream side of the channel as seen in the figure. Above the elevation, the channel widens to 3.75 m as shown in the figure If b2 = 3.75 m, what should be the maximum value of Δz to prevent suffocation? Draw the specific energy depth curve.
1. A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5 KN/m^3. What is the factor of safety against overturning? Find the location of the resultant. Find the maximum intensity pressure. Determine the minimum intensity pressure.
2.15 The tire of an airplane is inflated at sea level to 410 KN/m2 Assuming the tire does not expand, what is the pressure within the tire at elevation 9000 m? Assume standard atmosphere. Express the answer in KN/m2 and KN/m2, abs.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
An inverted right circular conical tank loses water out of a 4-in hole at the bottom. The radius of the top of the tank is 8 ft and its total height is 20 ft. Assume that the coefficient of contraction is 0.6. Solve for dh/dt. Solve for dV/dt.
The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific weight of the liquid is = 9.81 kN/m3. (3) For the inclined wall, determine the vertical depth to the center of pressure._________ (m)
A right circular cylindrical tank container, 2m in diameter and 4m high is 1/2 full of water. When rotated about its vertical axis at the rate of 60 rpm:A.) How many meters will the water surface drop at the center of the vessel? B.) What is the pressure, in kPa, at the base of the container along the perimeter? C.) What is the volume, in m^3, of the paraboloid formed by the rotation of the vessel? (Show complete solution)
aceeleration = 4.905 m/s^2 to the right What is the gage pressure at A? in kpa.
A rectangular pontoon 13.5m x 5.4m x 3.0m high floats in water with the 3.0m side vertical. The pontoon weighs 420kN and its centre of gravity is 1.2m above the base of the pontoon. Calculate the metacentric height of the pontoon when floating in:a. fresh waterb. sea water (ρ = 1025kg/m3) In which of these fluids does the pontoon have greater stability?