Consider pressurized water, engine oil (unused), and Nak (22%/78%) flowing in a 20-mm-diameter tube.(a) Determine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluidswhen the fluid temperature is 366 K and the flow rate is 0.01 kg/s.(b) Determine the mass flow rate, in kg/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for water and engineoil at 300 and 400 K and a mean velocity of 0.022 m/s.Part ADetermine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluidswhen the fluid temperature is 366K and the flow rate is 0.01 kg/s.LiquidUm (m/s)Xfdh (m)Xfd,t (m)wateriengine oiliiiNaki

Answered: Image /qna-images/answer/b5617dfe-fdda-419e-bfad-758cb8306383.jpg

Answered: Consider pressurized water, engine oil…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.40P

See similar textbooks

Similar questions

6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.
Air at atmospheric pressure and 27°C enters a 12-m-long, 1.5-cm-ID tube with a mass flow rateof 0.1 kg/s. The tube surface is maintained at a uniform temperature of 90°C. Calculate the average heattransfer coefficient and the rate of heat transfer to the air.
QS: Water at 15.56°C i to be heated in a 2-mm-ID tube until the exit temperature reaches 26.67+C. The tube wall temperature is maintained at 48.99-C and the inlet flow velocity is 0.3 m/s. Calculate the length of tube required in meters to accomplish this heating. Also calculate the total heating required, expressed in watts. Answers: L=0.13 m
A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is ?
Heat transfer problem Water flows through a thin-walled cylindrical tube of diameter 1 cm, maintained at a uniform temperature, ?s = 360 K. The inlet and outlet temperature of water was found to be ?i= 280 K and ?o = 355 K, respectively. (a) What is the log mean temperature difference in this case? (b) If the mass flow rate is 0.005 kg/s, what is the total rate of heat transfer from the tube to the water? (c) What is the Reynolds number corresponding to the given flow conditions? (d) Assuming fully developed flow in the entire tube, what should be the length of the tube to allow the abovementioned operating conditions ?
For these velocity distributions in a round pipe, indicate whether the kinetic-energy correction factor ∝ is greater than, equal to, or less than unity.
Consider a flow with pressure and temperature of 1 atm and 288 K. A Pitot Tube is inserted into this flow and measures a pressure of 1.555 atm. What is the velocity of the flow?
Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long
Flow Characterisitc (Entrance Effects) Why was there some disagreement between the actual Pitot tube velocity profile and the power law velocity profile?
Hot air (43 °C) at 1 atm flows into a circular plastic duct 50 m long at a rate of 0.2 m3/s. If the friction loss, hL, in the pipe does not exceed 6 m. Determine the diameter of the duct, the velocity of the fluid, and the Reynolds number.

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning