To determine the normal and shear stresses on the indicated plane, we must first determine the orientation of the inclined planerelative to the x face of the stress element. Determine the magnitude of the counterclockwise angle between the x face and theinclined plane. Assume Sx = 170 MPa, Sy = 105 MPa, Sxy = 85 MPa, and ß = 65°.SxSxyВSyAnswer: 0 = 25XO' For Mohr's circle, all angular measures are doubled; therefore, point n (which represents the state of stress on the n plane) onMohr's circle is rotated 20 counterclockwise from point x. From the Mohr's circle that you constructed on a piece of paper,determine the central angle between point n and the principal stress p1.Answer: p= ieTextbook and Media

Given Data: Sx=170 MPaSy=105 MPaSxy=85 MPaβ = 65° Find: (a) Determine the magnitude of the…

For Mohr's circle, all angular measures are doubled; therefore, point n (which represents the state of stress on the n plane) on Mohr's circle is rotated 20 counterclockwise from point x. From the Mohr's circle that you constructed on a piece of paper, determine the central angle between point n and the principal stress pl.

For Mohr's circle, all angular measures are doubled; therefore, point n (which represents the state of stress on the n plane) on Mohr's circle is rotated 20 counterclockwise from point x. From the Mohr's circle that you constructed on a piece of paper, determine the central angle between point n and the principal stress pl.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the principal stresses and the absolute maximum shear stress.
Determine the principal stresses, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the element in each case.
Draw Mohr’s circle for sx = sy = txy = 2 kPa. On the circle, label the axes and the principal stresses and their angles. Using three significant digits, determine the principal stresses and their angles, and the normal and shear stresses at q = 80 degree. The three gages from the strain rosette mounted on a steel shaft have the following readings: εa = 0.000316, εb = 0.000248, and εc = 0.000579. Determine the strain components: εx, εy, and Yxy.
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case.
Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure.
1) Determine the principal stresses. 2) Specify the orientation of the element
Determine the average normal stress developed at points A, B, and C. The diameter ofeach segment is indicated in the Figure below.
Using transformation equations of plane stress, determine the normal and shear stress components for X’-axis located 0.5 radians clockwise from x-axis. The non-zero stress components are given as follows, σx= 200 MPa, σy= 100 MPa, τxy= -50 MPa.
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100 MPa and the allowable axial or longitudinal stress is 45 MPa, determine the minimum thickness of the pipe when the internal pressure that can be applied to the tank is 1.25 MPa.
Determine the stresses at points A and B as a results of applying each of the following internal loads N = 300 N, V = 250 N, M = 120 N.m and T = 300 N/m. The diameter is 20 mm. You must show your detailed solutions