Consider the circuit shown in the figure, with =36.0 V,R, =50.02,R=1502 andL= 4.00 H.(a) Switch S, is closed. Just after S. is closed, what are the current i, through R, andthe potential differences V and Va ?AC(b) After S. has been closed a long time so that the current has reached its final, steadyvalue, what are i, . VAc and Ve ?(c) Find the expressions for i, , Vac and Ve as functions of time since S, was closed.Do your results agree with what you get in (a) and (b) ? Graph i, . Vsc and Ve as afunction oftime.RoLA

Given:- E=36.0 V, R0 =50.0 ohm, R=150 ohm andL=4.00 H Find:- (a) Switch S is closed. Just after S.…

Consider the circuit shown in the figure, with =36.0 V,R. =50.09 L=4.00H. [a) Switch S. is closed. Just after S. is closed, what are the current i, che potential differences V and Vea? [b) After S. has been closed a long time so that the current has reache value, what are i. V and V?

Consider the circuit shown in the figure, with =36.0 V,R. =50.09 L=4.00H. [a) Switch S. is closed. Just after S. is closed, what are the current i, che potential differences V and Vea? [b) After S. has been closed a long time so that the current has reache value, what are i. V and V?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter14: Inductance

Section: Chapter Questions

Problem 58P: Consider the circuit shown below. Find l1, l2and l3when (a) the switch S is first closed, (b) after...

See similar textbooks

Related questions

Q: Fill in the table with the missing values (assume the switch has been closed): 120 V I (2) (V) (A) |…

Q: 0.4 고 6V H www 20 л А. лееее 0.1 H ДАМА S 10 л

Q: R, = 122 R2 = 6n V, = 6.0v R3 = 22 V3 = 6.ov R4= 3n Vz = 4,0v

Q: For the following circuit in the figure below consider the direction of the current given. Determine…

A: I = 0.50 A R = 16.7 ohm

Q: If L = 3.7 H and R = 5.6 and e= 120 V, what is the delta v across the resistor 0.2s are the switch…

A: (given) Inductance (L) = 3.7 H Resistance (R) = 5.6 ohm Induced emf (ε) = 120 V Time (t) across the…

Q: In the circuit shown, the 16.0-V battery is removed and reinserted with the opposite polarity, so…

A: Given : V1 = 16 V V2 = 8 V R1 = 5 ohms R2 = 1.6 ohms R3 = 9 ohms R4 = 1.4 ohms

Q: A d.c. generator delivers current at 220 V, but owing to resistance of the cable leads, the…

Q: In the circuit shown. C switch S is closed and at the instant that the current in the circuit drops…

Q: For the circuit shown below, find the current through the 5.0 O resistor when Sj is closed and S2 is…

A: Given data: The resistance are, R1=2 ΩR2=5 ΩR3=1 ΩR4=3 Ω Voltage of battery is, V=3 V

Q: What would the Hall voltage be (in µV) if a 2.40 T field is applied across a 14-gauge copper wire…

Q: In the following circuit, find the current Ix, and the power associated to the dependent source.…

Q: The generator of a car idling at 1.582E+3 rpm produces 15.3 V. What will the output be at a rotation…

A: Given value--- angular speed 1 = 1.582E+3 rpm. Voltage 1 = 15.3 V. angular speed 2 = 2.886E+3 rpm.…

Q: In the circuit of the figure 8 = 3.20 kV, C = 7.80 µF, R1 = R2 = R3 = 1.03 MQ. With C completely…

Q: In the circuit shown, the 16.0-V battery is removed and reinserted with the opposite polarity, so…

Q: The potential difference required to pass a current 0.5 A in a wire of resistance 20W is 10V 0.01V O…

Q: the direction I, - 3.0A , Iq = 8.0 A , Ig =5,0 A and the figure Glve the current of the current…

A: I1 = 3 A , into the page I2 = 3 A , out of the pageI3 = 5 A , out of the page

Q: Evaluate the current at RL circuit with L=2 Henry, R=4 Ohm, E= 9 V after 3 seconds.

A: Given, Resistance,R=4Ω Inductance, L=2 H Emf of battery,E=9 V Time, t=3 s

Q: In the circuit of the figure & - 1.33 kV, C - 7.30 µF, R1 = R2 - R3 = 0.830 MQ. With C completely…

Q: A battery with Ɛ = 8.60 V and no internal resistance supplies current to the circuit shown in the…

A: Given: Emf, ε=8.60 V I∘=8.60 mAIa=1.00 mAIb=1.16 mA When the switch is open, Resistances R1,R2,R3…

Q: Consider a series RC circuit as in Figure below for which R =4.5 MQ, C=6.9 µF, and ɛ=30.0 V. Find…

Q: Considering the circuit shown below, determine the magnitude of the current in amperes 3 Ω + a b Μ…

Q: Q-2-3 in the circuit shown in the figure, the S switch is closed at t=0 and the capasitors, which…

Q: Derive the differential equation for current i(t) in series circuit below. The impressed emf is E(t)…

Q: Consider the arrangement shown in the figure below where R = 5.50 N, l = 1.10 m, and B = 2.25 T. B R…

Q: Assuming a steady current flow through a switch, find the time required for a (a) 20 C to flow if…

A: Write the expression of current I with relation to time t and charge Q. Part (a) Write the given…

Q: In the circuit shown, if the length of the potentiometer LAB 100 cm and the current in the…

Q: In the circuit given below, R= 10 Q. Find the current io 42 R 82 60 V 3i, The value of current lo in…

Q: In the circuit shown, R, = 30,R2 = 2 0, R, = 50,, = 4 V,E, = 10 V and e, = 6 V. Find the currents…

Q: What would the Hall voltage be (in µV) if a 2.40 T field is applied across a 13-gauge copper wire…

Q: Consider the circuit shown in the figure below, where R, = 5.00 N, R, = 9.00 N, and Ɛ = 11.0 V. 10.0…

A: All value given in circuit. We have to find--- Voltage across R1 ? Current across R1 ?

Q: 3.00 k2 d E Es 70.0 V 60.0 V 80.0 V R2 4.00 ka 2.00 k2 R

A: Consider the circuit diagram.

Q: Consider the circuit shown where the switch has been in position A for a long time. At time t = 0,…

Q: The switch S of the circuit shown below is closed at t = 0 . Determine (a) the initial current…

A: The expression for the current in RL circuits as a function of time can be given as, Here τ is the…

Q: The figure shows an LR circuit with L= 0.15 H, R = 25 2, and Vo = 36 V. The switch is initially…

Q: For the circuit shown below, ɛ = 20 V, L = 4.0 mH, and R = 5.0 N. After a steady state current is…

Q: For numbers 11 to 12, consider the circuit below. In this circuit Vpc = 6 V, R, = 100 N, R, = 200 Q…

A: Given that, R1= 100 ohm R2= 200 ohm R3= 300 ohm Voltage (Vdc)= 6 V

Q: Consider a series RC circuit for which R = 2.00 MQ, C = 5.00 µF, and ɛ = 30.0 V. Find the current in…

Q: How much energy is dissipated as heat during a 7minute time interval by a 2.80-kQ resistor which has…

Q: For the circuit shown, the current flowing through R, is 0.1740 A. If R2 = 13.59 Q V. V, the…

Q: In the accompanying figure, the rails, connecting end pieces, and rod all have a resistance per unit…

Q: For the following circuit in the figure below, What is the current ( in units of A) in the 10-Q…

A: Let's calculate the equivalent resistance from the parallel resistors

Q: ℇ = 100 V, R = 20.0 Ω, and L = 100.0 mH. The switch is closed att = 0. (a) What is the time constant…

A: Given: emf,ℇ = 100 V, Resistance, R = 20.0 Ω, Inductance, L = 100.0 mH =…

Q: Find the steady-state current in the RLC-circuit in Fig. 71 when R = 50 N, L = 30 H, C = 0.025 F, E…

Q: In the circuit below the current depends on the time t, and is given by / (t) = 1mAcos(wt). What is…

A: Given that,

Q: circuit of the figure & = 4.00 kV, C = 7.70 µF, R1 = R2 = R3 = 0.930 MQ. With C completely…

Q: How would you go about improving the determination of the electrical resistance of a given material…

A: Resistors are devices giving desired resistances in an electrical circuit. It is important to…

Q: Page No : Date: a currentof current be the Tnductor? A 18 H Tn ductor carv Pes QA. At what rate mast…

Q: The current in a single-loop circuit with one resistance Ris 3.75 A. When an additional resistance…

Q: Lets say the following electric currents flow into a junction of wires: 6.6 A (amperes or amps),…

A: According to KCL (Kirchhoff's circuit laws), the total current flowing into a junction is equal to…

Question

Consider the circuit shown in the figure, with =36.0 V,R, =50.02,R=1502 and
L= 4.00 H.
(a) Switch S, is closed. Just after S. is closed, what are the current i, through R, and
the potential differences V and Va ?
AC
(b) After S. has been closed a long time so that the current has reached its final, steady
value, what are i, . VAc and Ve ?
(c) Find the expressions for i, , Vac and Ve as functions of time since S, was closed.
Do your results agree with what you get in (a) and (b) ? Graph i, . Vsc and Ve as a
function oftime.
Ro
L
A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Two infinite solenoids cross the plane of the circuit as shown below. The radii of the solenoids are 0.10 and 020 m, respectively, and the current in each solenoid is changing such that dB/dt50.0T/s . What are die currents in die resistors of the circuit?
How long after switch S1 is thrown does it take the current in the circuit shown to reach half its maximum value? Express your answer in terms of the time constant of the circuit.
in the circuit shown in the figure, the S switch is closed at t=0 and the capasitors, which are completely empty, begin to fill. Here E=30V, C=3 uF and R=40 ohm. A) what is the time constant of the circuit, T, in the units of microseconds? B)when t=T, what is the total charge, in units of microcoulomb?
The capacitor in the circuit shown below is initially uncharged. The switch is closed at t = 0 s. ΔVbattery = 60 V, C = 2.0 F, and R = 3.0 Ω. What is the current in the circuit at t = 5.2 s, in Ampere?
After being closed for a long time, the switch S in the circuit shown in the figure below is thrown open at t = 0. In the circuit, E= 24.0 V, RA = 3.90 kΩ, RB = 7.20 kΩ, and L = 646 mH.
ℇ = 100 V, R = 20.0 Ω, and L = 100.0 mH. The switch is closed att = 0. (a) What is the time constant of the circuit shown below? (b) Find the currentat t = 0.050 sec, (c) at what time the current is 40% of its maximum value?
The capacitor in the circuit shown below is initially uncharged. The switch is closed at t = 0 s. ΔVbattery = 30 V, C = 3.0 F, and R = 2.0 Ω. At sometime after the switch is closed, the current in the circuit is measured to be 6.1 A. What is the charge on the capacitor at this time, in Coulomb?
The capacitor in the circuit shown below is initially uncharged. The switch is closed at t = 0 s. ΔVbattery = 60 V, C = 2.0 F, and R = 3.0 Ω. What is the current in the circuit immediately after the switch is closed, in Ampere?
Consider the circuit shown below. Find I1, I2, and I3 when (a) the switch S is first closed, (b) after the currents have reached steady-state values, and (c)at the instant the switch is reopened (after being closed for a long time).
The figure shows four closed paths around a wire of current I. Which of the following statement is correct concerning the magnitudes of Bds :
In the circuit below, the switch has been in the open position for a long time. At t=0, the switch is turned on. If the current at time t=3.3 ms reaches half of its maximum value, L=68 mH, and ℰ=17 V, find:the time constant τ= ms,the resistance R= Ω,the maximum value of the current, Imax= A.If the switch is open again, after what time, the current will reach the half of its value?t1/2= ms.
In the figure below, R1 =10.0kΩ, R2 =15.0kΩ, C=0.40μF, and the ideal battery has an emf E=20.0V. First, the switch is closed until the system reaches steady state; then, the switch is opened at time t = 0 and the capacitor starts to discharge. What is the current in R2 at t = 3.00 ms?