in the circuit shown in the figure, the S switch is closed at t=0 and the capasitors, which are completely empty, begin to fill. Here E=30V, C=3 uF and R=40 ohm.A) what is the time constant of the circuit, T, in the units of microseconds?B)when t=T, what is the total charge, in units of microcoulomb? (1) AŞAĞIDAKİ SORULARI BURADA VERİLEN BİLGİYE GÖRE YANITLAYINIZ.RwwCŞekildeki devrede t = 0 anında S anahtarı kapatılarak, tamamen boş durumda bulunan,kapasitörler dolmaya başlıyor. Burada E = 30 V, C = 3 µF ve R = 40 N.RA) Devrenin zaman sabiti T, mikrosaniye biriminde nedir?Answer:B) t = T olduğunda kapasitörlerde biriktirilen toplam yük mikrocoulomb biriminde nedir?Answer:

Answered: Image /qna-images/answer/aad0cfcd-9f02-4f8a-a949-7af905587f12.jpg

in the circuit shown in the figure, the S switch is closed at t=0 and the capasitors, which are completely empty, begin to fill. Here E=30V, C=3 uF and R=40 ohm. A) what is the time constant of the circuit, T, in the units of microseconds? B)when t=T, what is the total charge, in units of microcoulomb?

in the circuit shown in the figure, the S switch is closed at t=0 and the capasitors, which are completely empty, begin to fill. Here E=30V, C=3 uF and R=40 ohm. A) what is the time constant of the circuit, T, in the units of microseconds? B)when t=T, what is the total charge, in units of microcoulomb?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter28: Current And Resistance

Section28.3: Current Density

Problem 28.3CE

See similar textbooks

Similar questions

What current flows through a 2.54-cm-diameter rod of pure silicon that is 20.0 cm long, when 1.00 × 103 V is applied to it? (Such a rod may be used to make nuclearparticle detectors, for example.)
i provided a solution for the same problem but while using 5.26 T instead of 5.37 T. In the solution provided it gives the answer in eV but for my question, i need the answer to be in micro electron Volt (μeV).
If the acceleration voltage is 150 kV, calculate the half-life thickness knowing that the 10% reduction thickness is 0.256 mm.
How much work is needed to carry an electron from the positive terminal to the negative terminal of a 9.0-V battery. (e = 1.60 × 10-19 C , melectron = 9.11 × 10-31 kg) *my incorrect answer was: 14.4 × 10-19 J/C
If three cells of 1V, 1.5V, 2V are connected in parallel, then the total e.m.f will be:
What quantity of electrons that will move from the positive terminal to a negative terminal of a battery whose emf is 1.5 volts during the conversion of 1/4 joule of chemical energy?
The net energy requirement in a place was approximately 2.82 x 106 GWh. What is the equivalent of this energy in quad?
How much work is needed to carry an electron from the positive terminal to the negative terminal of a 9.0-V battery. (e = 1.60 × 10-19 C , melectron = 9.11 × 10-31 kg) Group of answer choices 17 × 10-19 J 14.4 × 10-19 J/C 14.4 × 10-19 J 9.0 J 1.6 × 10-19 J
Show that for V less than zero, InetI0.
A metal object having a length (10m), cross section area (0.5 mm2), and resistance (0.52) is connected to a potential difference source of 5V at room temperature. If the density of free electrons equals (8×1025 electron/m³), Calculate the thermal velocity.
An electric toaster uses nichrome for its heating element. When a negligibly small current passes through it, its resistance at room temperature (27.0 °C) is found to be 75.3 Ω. When the toaster is connected to a 230 V supply, the current settles, after a few seconds, to a steady value of 2.68 A. What is the steady temperature of the nichrome element? The temperature coefficient of resistance of nichrome averaged over the temperature range involved, is 1.70 × 10-4 °C-1.
A certain x-ray tube operates at a current of 7.00 mA and a potential difference of 80.0 kV.What is its power in watts?