Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected toloads as shown in the figure below.Find the magnitude of maximum normal stress, in section a-a innumeric value without units upto 4 digits after decimal point, but with correct sign.Enter onlyMPa:200 mm200 mmR.Section a-a400 N800 N

Answered: Image /qna-images/answer/ac386528-9476-4f3c-9682-c5968373bd0f.jpg

Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the magnitude of maximum normal stress, g in section a-a in MPg: Enter only numeric value without units upto 4 digits after decimal point, but with correct sign. 200 mm 200 mm Section a-a 400 N 800 N D. P.

Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below. Find the magnitude of maximum normal stress, g in section a-a in MPg: Enter only numeric value without units upto 4 digits after decimal point, but with correct sign. 200 mm 200 mm Section a-a 400 N 800 N D. P.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A simply supported wood beam is subjected to point load P at mid-span. The normal stress on element C is known to be sx= 12 MPa. Find the maximum shear stress on the element and show the state of stress on a sketch of a properly oriented element.
At a point on the web of a girder on a gantry crane, the stresses acting on the x face of a stress element are s= 6250 psi and ??xy= 1425 psi (see figure). What is the allowable range of values for the stress ??. if the maximum shear stress is limited to t0 = 2150 psi?
- 7.3-12 A simply supported beam is subjected to two point loads as shown in the figure. The stresses on element A are txy= 20 kPa. Find the principal stresses on element A and show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
3-17 The stresses at a point along a beam supporting a sign (see figure) are sx= 2250 psi, sy,. = 1175 psi, and txy = -820 psi. (a) Find the principal stresses. Show them on a sketch of a properly oriented clement. (b) Find the maximum shear stresses and associated normal stresses. Show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a