2:56docs.google.com aالسوال الأولThe concepts relating to Ohm's lawConsider the electric circuit and table shownin Figure Q.1. Fill the table below considering;a) R=1 kN b) R=10 kN. What is the relationshipbetween the slope of the plot line and the?circuit resistanceEsREsCurrent (mA)10Fig. (Q.1) Ohm's lawإضافة ملفصفحة 4 من 5محو النموذجالتاليرجوع2->...

Slope is Inversely proportional to Resistance

Consider the electric circuit and table shown in Figure Q.1. Fill the table below considering; a) R=1 kQ b) R=10 kn. What is the relationship between the slope of the plot line and the ?circuit resistance Es R Es Current (mA) 10 Fig. (Q.1) Ohm's law إضافة ملف

Consider the electric circuit and table shown in Figure Q.1. Fill the table below considering; a) R=1 kQ b) R=10 kn. What is the relationship between the slope of the plot line and the ?circuit resistance Es R Es Current (mA) 10 Fig. (Q.1) Ohm's law إضافة ملف

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A factory space of 33 m x 13 m is to be illuminated with an average illumination of 72 Im/m² by 200 W lamps. The coefficient of utilization is 0.4 and the depreciation factor is 1.4. Calculate the number of lamps required. The lumen output of a 200-W lamp is 2,7301m. 30 35 45 40
A barangay power station supplies 60kW to a load over 2,500ft, 100 mm², two conductors copper feeder. The resistance of which is 0.0078 ohm per 1,000 ft the bus bar voltage is maintained constant at 600V. Determine the load current.
The dark saturation current of a solar cell is 1.6X10-8 A/m2 , the cell temperature is 333 K, the shortcircuit current density is 194 A/m2 , Vmax is 0.436 V and the available solar radiation is 805 W/m2 . The Boltzmann’s gas constant is 1.381X10-23 J/K and the electronic charge is 1.602X10-19 J/V. Calculate i) Open-circuit voltage (Voc) ii) Current density at maximum power (Imax) iii) Maximum power (Pmax) and iv) % Maximum efficiency (ηmax).
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A substation supplies power by four feeders to its consumers. Feeder No. 1 supplies six consumers whose individual daily maximum demands are 70 kW, 90 kW, 20 kW, 50 kW, 10 kW, and 20 kW, while the maximum demand on the feeder is 200 kW. Feeder No. 2 supplies four consumers, whose daily max. demands are 60 kW, 40 kW, 70 kW, and 30 KW, while the maximum demand on feeder No. 2 is 160 kW. Feeders Nos. 3 and 4 have a daily maximum demand of 150 kW and 200 kW respectively, while the maximum demand on the station is 600 kW. Determine the diversity factor for the four feeders. 1.18 1.25 1.30 1.36
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:Where the voltage between conductors does not exceed 300 V and the roof has a slope of not less than 100mm in 300mm, the clearance can be reduced to: 500 mm 800 mm 1000 mm 900 mm
In a design task, a wire of 2000 m requires to exhibit a voltage drop of 2.5 Vwhen 3.2 A of current passes though it. Based on the Table Q1 (b) below, inyour opinion, which of the wire is the most suitable for aviation when the fuelsaving is another factor to be considered as well.
1. An LRT car, 5 km distance from the Tayuman, takes 100 A over a 100 mm hard-drawn copper trolley wire having a resistance of 0.270 ohms per km. The rail and ground return has a resistance of 0.06 ohm per km. If the station voltage is 750 V, what is the voltage of the car? 2. A carbon resistor dissipated 60 W of power from a 120 V source at 20°C. How much energy will be dispersed in the resistor at 120°C if connected across the same source? Assume the temperature coefficient of carbon at 20°C is -0.0005 per °C?
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:It is required to provide illumination of 150 meter-candle in a factory hall 45m x 15m. Assume that the depreciation factor is 0.80, the coefficient of utilization is 0.40 and the efficiency of the lamp is 20 lumens per watt. Calculate the number of 250-W lamps. 63 62 61 60
Estimate the dielectric losses in the solid specimen subjected to an alternating field of 40KV/cm, has an absolute permittivity of 4.445 x10-11 and the loss angle of that solid dielectric material is 0.28647at Oman power frequency. And also the same specimen while subjected to 3 KV/cm DC supply with the resistance value of 10 Mega Ohm, then determine the heat generated in the specimen.
A 500 W heating coil, designed to operate at 110V, it is made of 0.500mm diameter nichrome wire. a) If the resistivity of nichrome remains constant at 20.0 ° C, determine the length of the wire used. b) What will be the power given to the coil from part (a) when heated to 1200 ° C? c) If the electric company charges B/0.16 per kW-h, how much you will have to pay to keep the heating coil working at this temperature for 45 minutes?
Provide complete solution. ASAP!!!!
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design