Consider the feedback control system shown in figure below. The steady- state error for a step input in terms of the gain K. The overshoot for the step response for K- 100. are, respectively. Controller K(s + 50) Process 46.24 Ris) Yis) s+ 200 + 16.7s + 72.9 Sensor 425 s+ 425 0.1/K 25 6.7/6.7+K 25 1.

Consider the feedback control system shown in figure below. The steady- state error for a step input in terms of the gain K. The overshoot for the step response for K- 100. are, respectively. Controller K(s + 50) Process 46.24 Ris) Yis) s+ 200 + 16.7s + 72.9 Sensor 425 s+ 425 0.1/K 25 6.7/6.7+K 25 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

BelowIn the unit feedback system given the shape, G(s),is given as. When a unit ramp is applied to the input of the system, 2% of the steady-state error and unit to the inputWhen the step is applied, it is desired that the percentage exceedance rate is 9.25% and the settling time is 0.58 s.1-In this case, which of the following is the approximate value of the constant a?
a) Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. b) Define the gain and phase margin, this time on the nyquist curve.
A For a monolithic negative feedback system defined by the open path function, find the gain range (to operate the system at steady state
BelowIn the unit feedback system given the shape, G(s),is given as. When a unit ramp is applied to the input of the system, 2% of the steady-state error and unit to the inputWhen the step is applied, it is desired that the percentage exceedance rate is 9.25% and the settling time is 0.58 s.1-In this case, which of the following is the approximate value of the constant a? 2-In this case, which of the following is the approximate value of the constant b? 3-Looking at the unit step response of the systemWhat is .peak time?
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Figure Q2 shows the block diagram of a flight control system.a) Derive the system transfer function.b) Find out the system gain, natural frequency and damping ratio for this systembased on the standard form of second order systems.c) If K1 = 2 and K2 = 10, use the standard response sheet to find out the systemsteady-state value, overshoot and 63% rise time, with a unit step input.
Study the stability as a function of the gain k of the following system using Nyquist and Routh Hurwitz method
For the unity-feedback system with G(s) = K / s(s + 5)(s + 11): i. Find the gain K for the uncompensated system to operate with a 30% overshoot.ii. Find the peak time (Tp) and Kv for the uncompensated system.iii. Design a lag–lead compensator to decrease the peak time by a factor of 2, decrease the percent overshoot by a factor of 2, and improve the steady-state error by a factor of 30. Assume the lead compensator zero is at -5. Please specify all poles, zeros, and gains.
a) What is the currenr flowing in the input resistor (i1) for t>0? b) What is the value of the feedback resistor Rf? c) What is the capacitor voltage in steady state (Vc( ∞ ))?
For a unity-feedback system with G(s) = K / s(s + 20)(s + 40) operating with a 20% overshoot, design a compensator to decrease the settling time by a factor of 2 without affecting the percent overshoot:i. Find the uncompensated system's dominant poles, gain, and settling time. ii. Find the compensated system's dominant poles and settling time. iii. Find the compensator's pole position and required gain. (Assume the compensator’s zero is at -20).
Assume any finite duration discrete time signal x(n) following the necessary condition satisfying the property of energy signal of your own choice. Now consider a discrete time system whichperforms Amplitude scaling operation followed by time reversal operation based on y(n) = ax(n) + x(-n). Sketch the output of resultant signal. Now classify and justify your answer with necessary and sufficient conditions that whether the above system based on all types of system.
Analyze the circuit below and provide what are being ask in the problem e.f. Determine the DC voltagesDetermine the DC currents??1,, ??2,, ??1, , ??, and2 , ??1 and ??2 g. Solve for the input and output impedances??1 ??2 ??1 ??2 ??2 h. Solve for the voltage gain and current gain