Consider the following numerical data that apply to a viscously-data spring-mass system subjected to forced vibration, as shown in figure P3 below: m = 130.0 kg, k = 4.0 kN/m, c = 950 N- s/m and P= 450 Sin pt N. For what excitation frequency (or frequencies), the steady-state amplitude of the system will be less than 1.65 mm? Figure P3. P-P, sin pe x(1)

Consider the following numerical data that apply to a viscously-data spring-mass system subjected to forced vibration, as shown in figure P3 below: m = 130.0 kg, k = 4.0 kN/m, c = 950 N- s/m and P= 450 Sin pt N. For what excitation frequency (or frequencies), the steady-state amplitude of the system will be less than 1.65 mm? Figure P3. P-P, sin pe x(1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a SDOF system having a mass m = 30 kN s2 /m, damping c = 50 kNs/m and stiffness k = 4000 kN/m. Determine natural frequency, damping ratio and critical damping. For x(0) = 0.02 m, and x . (0) = 0.1 m/s. Find the solution of the equation of motion. Hence, plot inertia, damping and spring force vs time for free vibration.
An underdamped shock absorber is to be designed for a motorcycle of mass 200 kg (Fig. 2.30(a)). When the shock absorber is subjected to an initial vertical velocity due to a road bump, the resulting displacement-time curve is to be as indicated in Fig. 2.30(b). Find the necessary stiffness and damping constants of the shock absorber if the damped period of vibration is to be 2s and the amplitude x1 is to be reduced to one-fourth in one half cycle. Also find the minimum initial velocity that leads to a maximum displacement of 250 mm.
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
The mass of a spring-mass system, with m = 12 kg and k = 35 kN/m, vibrates on a horizontal surface under a harmonic force of magnitude 300 and a frequency of 19 Hz. Find the resulting amplitude of steady state vibration. Assumethe coefficient of friction between the mass and the horizontal surface as 0.25
The structure shown in figure has a mass of 100 kg and a translational stiffness of 40,000 N/m. It is excited by a harmonic force having an amplitude Po = 500 N and an excitation frequency ω = 15 rad/s. The damping factor for the structure is ξ = 0.1. The initial conditions are u(0) = 6 cm and ώ(0) = 0. For the steady-state vibration determine: (a) The amplitude of the stady-state displacement. (b) Its phase with respect to the exciting force. (c) The maximum velocity and acceleration of the response. (d) Determine the equation that describes the total displaement of the structure as a function of time.
A machine is represented as a single degree of freedom spring-mass-damper system. The machine has a total mass of (109)kg, an out-of-balance mass 0.125 kg, eccentricity of 0.01 m, coefficient of damping (109)N/ (m/sec), and spring stiffness (1009) N/m. The rotational speed of the machine is 3000 rpm. Determine the maximum amplitude of vibration due to out-of-balance. Suggest a method for the control of vibration caused due to out-of-balance.
Mechanical Vibrations Question is image A 300-kg machine is attached to an elastic foundation of stiffness 3.1 x E6 N/m and damping ratio 0.06. When excited by a frequency squared excitation at very large speeds, the machine's steady-state amplitude is 10 mm. What is the maximum steady-state amplitude the machine would experience at lower speeds?
Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and feltare kept in series as shown in Figure Q1(b). The natural rubber slab has a stiffnessof 3000 N/m and an equivalent viscous damping coefficient of 110 Ns/m. The feltslab has a stiffness of 12,200 N/m and an equivalent viscous damping coefficient of170 Ns/m. (i) Sketch the single degree of freedom spring-mass-damper system(ii) Determine the undamped and damped natural frequencies of the system inthe vertical direction. Neglect the mass of the isolator
A spring mass system with a natural frequency fn = 20 Hz is attached to a vibration table. Thetable is set to vibrate at 16 Hz, with a maximum acceleration 0.25 g. Answer the followingquestions. Justify your answers d. What is the maximum acceleration of the mass assuming the packaging can be modeled asa viscous damper with a damping ratio of 0.2?e. Is the motion of the mass in phase or out of phase with the motion of the table?
Example of Vibration System Analysis. Include appropriate model and complete label for mass, damping and spring elements.
A vertical spring-mass system is submerged in oil. The spring has a stiffness coefficient of 3 N/m, and the mass is 1 kg. If the dampened angular frequency omega_d of oscillation is 0.866 Hz, find the damping coefficient b for the oil and how long it takes the spring to reach 50 percent of its original amplitude.
For a system with mass 10 kg, spring constant 100 N/m, damping ratio 1 kg/s, rotating unbalance of 0.1 kg, radius 100 cm, and driving frequency 50 Hz, what is the amplitude of the particular solution? What is the phase lag of the particular solution?