Consider the op-amp circuit shown in Figure below, where the op amp has infinite inpuresistance and zero output resistance but finite open-loop gain.a) Prove that B = R1/R1 + R2.b) If R1 10 ka, find R2 that results in G 10 V/V for the following three cases:i A = 1000 V/VAii. A = 200 V/Viii. A = 15 V/V%3DVoVsR2

Answered: Image /qna-images/answer/990b7f8b-9e11-4ca7-a997-a37d39811635.jpg

Consider the op-amp circuit shown in Figure below, where the op amp has infinite inpu esistance and zero output resistance but finite open-loop gain. ) Prove that B = R1/R1 + R2. - ) If R1 10 kN, find R2 that results in G = 10 V/V for the following three cases: i A= 1000 V/V ii. A = 200 V/V iii. A = 15 V/V +, Vo Vs R2 R1

Consider the op-amp circuit shown in Figure below, where the op amp has infinite inpu esistance and zero output resistance but finite open-loop gain. ) Prove that B = R1/R1 + R2. - ) If R1 10 kN, find R2 that results in G = 10 V/V for the following three cases: i A= 1000 V/V ii. A = 200 V/V iii. A = 15 V/V +, Vo Vs R2 R1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.
The inverting amplifier in the circuit shown has an input resistance of 500 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 300,000. Assume that the amplifier is operating in its linear region. 1. Calculate the voltage gain (vo/vg) of the amplifier. 2. Calculate the value of vn in microvolts when vg=1 V. 3. Calculate the resistance seen by the signal source (vg). 4. Repeat (a)–(c) using the ideal model for the op amp.
For the circuit shown, determine the range (i.e., maximum and minimum values) of V1 such that the op-amp operates in the linear region. Assume that R1 = 9.4 kΩ , R2 = 1.6 kΩ , R3 = 4.0 kΩ, RF = 200 kΩ, V2 = 40 mV, V3 = 100 m, and Vcc = 5 V.
Consider the following op amp configuration.(a) Choose R2 such that the ideal voltage gain is Av = 40dB and draw the amplifier’stransfer characteristic.(b) Find the amplifier’s input and output resistances.(c) If the op amp’s internal gain is Ao = 120dB, what is the expected voltage gain ofthe entire network?
For the op-amp circuit shown below, find the value of vO, where R1 = 19 Ω, R2 = 14 Ω, R3 = 18 Ω, R4 = 14 Ω, Rf = 11 Ω, VS1 = 15 V, and VS2 = 3 V.
In the circuit below, assuming the ideal opamp, we ask a) determine the circuit gain (Avf = V2 / V1). b) Calculate the gain value when R1 = R3 = 10KΩ and R2 = 16kΩ answer a) Avf=1((R1+R3)/R2) b) Avf=2,25
Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
Please show that gain = -(1-n)/(1+nA) , n = R1/(R1+R2) and compare to gain of ideal op amp. Calculate the input and output impedances, and lastly whats the point of the resistor R1//R2 on the non-inverting input? What would be the best value for this resistor? (pretending it wasn't given that the value is R1/R2).
A non-inverting op-amp circuit has the open loop gain of 136 and the resistances R1=3500 Ω and R2 = 3.8 kΩ . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain. (a) The actual value of voltage gain Answer for part 1 (b) The ideal value of voltage gain Answer for part 2 (c) Error, when ideal voltage gain is compared with actual voltage gain. Answer for part 3 (d) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Q2. For the op-amp circuit as shown below, given that RS = 50.5 kΩ, RL = 9 kΩ, R1 = 10 kΩ, R2 = 11 kΩ, R3 = 6 kΩ, R4 = 4 kΩ, R5 = 1.8 kΩ. (a) Determine the voltage gain G1=vO1/vS: (b) Determine the voltage gain G2=vO/vS:
1. Find the Thévenin equivalent circuit with respect to the output terminals a, b for the inverting amplifier shown. The dc signal source has a value of 880 mV. The op amp has an input resistance of 500 kΩ, an output resistance of 2 kΩ, and an openloop gain of 100,000. 2. What is the output resistance of the inverting amplifier? 3. What is the resistance (in ohms) seen by the signal source vs when the load at the terminals a, b is 330 Ω?