Consider the system in (Figure 1) gure k-5 lb/in. <1 of 1 Determine the smallest amount the spring at B must be compressed against the 0.2-lb block so that when the block is released from Bit slides along the smooth surface and reaches point A Express your answer in inches to three significant figures. VAΣ Ivec Submit Request Answer Provide Feedback ? in. N

Consider the system in (Figure 1) gure k-5 lb/in. <1 of 1 Determine the smallest amount the spring at B must be compressed against the 0.2-lb block so that when the block is released from Bit slides along the smooth surface and reaches point A Express your answer in inches to three significant figures. VAΣ Ivec Submit Request Answer Provide Feedback ? in. N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.73P: The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the...

See similar textbooks

Similar questions

Question 13.56 (Please do problem 13.56 only.) A spring with free length 1.2m is attached to a collar of mass of 20kg. if the collar is released from at position A to slide down the smooth vertical rod shown. If the lowest position readed by the collar is A2, where b=2m, determine the modulus k of the spring.
If spring is found to extend 20mm for each 2kg of mass, the defelaction of spring carrying a mass of 10kg is A)200mm B)1m C)0.1m D)10m
Need help in 15 minutes. ASAP. A 75-kg block is attached to a cable. The cable is then attached to a rotating assembly with a mass moment of inertia of 18 kg-m^2. The bearing friction applied at the rotating assembly equivalent to a couple of 45 N-m CCW. The block's downward speed is initially at 2 m/s. What is the total work done by the system after the rotating assembly has rotated 1.5 radians CW? What is the speed of the 75-kg block after the rotating assembly rotated 1.5 rad CW?
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
The crate shown is held against wedge B by a spring. The spring is 92.5% of its original uncompressed length l=2.50m , and the spring constant is given as k=1350N/m . The coefficient of static friction at all contacting surfaces is μs=0.150 . The mass of the crate is m=28.0kg . The angle is θ=14.0∘ . Neglect the mass of the wedge. Assume the crate only moves in the y direction and that wedge A cannot move.(Figure 1) Part A - Determining the normal force exerted by the crate on the wedge Determine the normal force Nc that the crate exerts on the wedge when the system is at rest. Express your answer to three significant figures and include the appropriate units. Part B - Finding the smallest horizontal force P to move the crate upward Determine the magnitude of the smallest horizontal force P that is necessary to begin moving the crate upward. Express your answer to three significant figures and include the appropriate units.
The 10 N cylinder moves in a friction tube. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. The system rotates around a fixed z-axis. In the case where d = 0.12 m, what is the coefficient of friction for the cylinder to have a constant velocity of 9.825 m / s?
The piece has a mass of 43 kg and is supported by springs with a common spring constant of 4445 N / m. What is the frequency of the vibration of the body when a damper with a damping factor of 80 kg / s is added to the suspension? Enter the answer in Hertz to one decimal place.
The pendulum consists of a uniform slender rod and a solid cylinder. The centre of gravity G of the pendulum is a distance L from the pin connection O. The radius of gyration of the pendulum about G is kG. The pendulum is displaced a small distance from its equilibrium position and then released. Take L=2.521 m (a) Give the differential equation that describes the motion by filling in the coefficient of θ (with at least 4 significant figures): the above equation is in one of the images. (b) What is the natural period of vibration of the pendulum (with at least 4 significant figures):
Question 3 The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant 3.1. Draw the port governor mechanism and clearly lable it. 3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
Please respond as quickly as possible, USE THE DATA SHOWN IN THE TABLE. Distances are in centimeters The mechanism shown is used to carry out experimental tests on different industrial springs that are placed between the wall and point A. The rigid reinforcement that holds the spring at A moves through the horizontal beam by means of the 4 frictionless rollers. The piston CD is compressed by stretching the spring at A. For the situation in the position shown the spring is stretched a distance s and has an elongation constant of 2000N / m. The weight of the system can be considered negligible. Determine: 1.The magnitude of compressive force exerted by the piston at the position shown. 2.The magnitude of the force experienced by the bolt at E.
The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant: 3.1. Draw the port governor mechanism and clearly lable it. (06)3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.