Determine the normal force it exerts on the ground. Express your answer to three significant figures and include the appropriate units. The 10-kg disk turns around the shaft AB, while the shaft rotates about BC at a constant rate of Wa = 6.5 rad/s. The disk does not slip. Neglect the mass of shaft AB. (Figure 1) HA ? Value Units Submit Request Answer Part B Figure 1 of 1> Determine the frictional force it exerts on the ground. Express your answer to three significant figures and include the appropriate units. C HẢ ? 2 m Value F1 0,4 m Units Submit Request Answer P Pearson

Determine the normal force it exerts on the ground. Express your answer to three significant figures and include the appropriate units. The 10-kg disk turns around the shaft AB, while the shaft rotates about BC at a constant rate of Wa = 6.5 rad/s. The disk does not slip. Neglect the mass of shaft AB. (Figure 1) HA ? Value Units Submit Request Answer Part B Figure 1 of 1> Determine the frictional force it exerts on the ground. Express your answer to three significant figures and include the appropriate units. C HẢ ? 2 m Value F1 0,4 m Units Submit Request Answer P Pearson

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
A press tool machine uses a flywheel in the form of a solid steel disc 0.7 m diameter and 0.1 m thick rotating with a mean speed of 60 rev/min. The density of the steel is 7830 kg/m^3. The press is operated once every 5 revolutions and a torque of 2000 Nm is exerted on the tool for a duration of 0.05 seconds. determine the following: The energy absorbed is replaced during the rest of the cycle. The coefficient of fluctuation of speed .The maximum and minimum speeds of the flywheel
The G weight of the figure, when descending, rotates the axis fixed to drums, which are supported by two cylindrical bearings of known dimensions, with known angular velocity ω. Determine the value of weight G, neglecting the rigidity and friction in the rope and assuming that the velocity diagram in the lubricant is linear. Given Data: μ = 8x10⁻² N/m², Di = 0.100 m,D = 0.02 m, Li = 0.1 m,De = 0.101 m, ω = 20/π rd/s
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
The disk with a mass of 0.4 kg and a radius of 2 cm (I = 1 / 2mr ^ 2) slows down as it rolls on a flat surface. While the motion of the disc is the result of the moment of inertia, the friction coefficient is 0.1. Calculate the torque responsible for the deceleration of the disc
The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
A speedboat with a mass of 529 kg (including the driver) is tethered to a fixed buoy by a strong 28.3 m cable. The boat's owner loves high speed, but does not really want to go anywhere. So the owner revs up the boat's engine, makes a lot of noise, and runs the boat in circles around the buoy with the cable supplying all the necessary centripetal force. When the tension of the cable is steady at 12300 N, with what force is the boat's engine pushing the boat? Different physics textbooks treat drag force somewhat differently and use different formulas. For the present purpose, take the water's drag force on the boat to be (450 kg/m)×v2, where v denotes the boat's speed. Ignore any drag force on the cable. What is the force of the engine?
A drum of mass Ma and radius a rotates freely withinitial angular velocity ωa0. A second drum with mass Mb and radiusb > a is mounted on the same axis and is at rest, although it is free torotate. A thin layer of sand with mass Ms is distributed on the innersurface of the smaller drum. At t = 0, small holes in the inner drumare opened. The sand starts to fly out at a constant rate λ = dm/dtand sticks to the outer drum. (a) Explain, in detail, why the angularvelocity of the inner drum will remain constant. (b) Determine theangular velocity of the outer drum ωb(t). Ignore the transit time ofthe sand
A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractorif it is operating at an altitude of 1,000 m. above sea level, at an averagetemperature of 25oC, and at an average speed of 12 km/hr. Take rimpull efficiencyas 85%.
Indicate for which types of systems the theoretical results obtained by the kinetic theory for the distribution of speeds can be applied. explain it.