Consider Two same size PV Modules which are connected in Parallel. The specification of each module is given as: Number of cells = 36, Area of each cell is 12 cm x 12 cm. (Assume the necessary data) Choose from the following the correct statement. a. The output voltage of this panel is 18 V, the output power is 155W b. The output voltage is this panel 18V, the output power is 75W c. The output voltage is this panel 36 V, the output power is 155W d. The output voltage is this panel 36 V, the output power is 75W

Consider Two same size PV Modules which are connected in Parallel. The specification of each module is given as: Number of cells = 36, Area of each cell is 12 cm x 12 cm. (Assume the necessary data) Choose from the following the correct statement. a. The output voltage of this panel is 18 V, the output power is 155W b. The output voltage is this panel 18V, the output power is 75W c. The output voltage is this panel 36 V, the output power is 155W d. The output voltage is this panel 36 V, the output power is 75W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

At what height are the telephone outlets in this residence mounted? Give measurement to center. _____
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____ b. What is the minimum number of small-appliance circuits permitted by the Code? _____ c. How many small-appliance circuits are included in this residence? ____
Explain the difference between cumulative- and differential-compounded connections.
An ac resistance is higher than a dc resistance. True False
With a neat diagram ,explain about the working of Dual Slope ADC.
Maximum dc source current is defined by NEC 690.8(A) as the sum of parallel module rated short circuit currents multiplied by? A.110% B. 125% C. 150% D. 200%
this represents an OLTC system, taken from the matlab program, explain what the elements used are, and why it is used for the OLTC system.
Given a voltage divider configuration of a D-MOSFET with IDSS = 12mA, VP = -3V, yos = 35µS, R1 = 91MΩ, RD = 6.8kΩ, RS = 3.3kΩ, VDD = 18V(i) Draw a complete circuit as describe above.(ii) Determine the operating point, IDQ and VGSQ using mathematical approach.(iii) Determine the operating point, IDQ and VGSQ using graphical approach.(iv) Voltage across drain and source terminals, VDS .
Consider the circuit of Figure 1 using VCC = 10 volts, R1 = 10 kΩ, R2 = 3.3 kΩ, Re = 4.7 kΩ and Rc = 5.6 kΩ. Using the approximation of a lightly loaded “stiff” voltage divider, determine the ideal endpoints of the DC load line and the Q point, and record these in Table 1.1. Can you show process of solution
Derive the Rs formula from the voltage divider formula. Show your steps. Given that the internal resistance of the batteries is very low, how would you make the calculations more accurate knowing the switch resistance? Do you think we should consider the leads and connector resistances to? Should those be added to the load resistor? Answer in full sentences what you think.
Can you explain in detail on how to solve this?Determine current ID graphically using load line analysis, if Zener voltage is 3V.