Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output power is 2.25W and the output current is 0.09A b. The output power is 540W and the output current is 45A c. The output power is 54W and the output current is 2.25A d. The output power is 54W and the output current is 4.5A

Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output power is 2.25W and the output current is 0.09A b. The output power is 540W and the output current is 45A c. The output power is 54W and the output current is 2.25A d. The output power is 54W and the output current is 4.5A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
With a neat diagram ,explain about the working of Dual Slope ADC.
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These power supplies include transformers that change the voltage of the AC that comes through wall outlets, rectifiers to save it from AC to DC and a filter that removes noise from the peaks and troths of the AC power waves.The DC-to-AC Converters are used to charge the batteries in the vehicles. These circuits are mainly used for driving low-power AC motors and are used in a solar power system. The DC to AC converters can be used in dc transmission lines for transmitting power to loads. QUESTION: What do you think is the main reason why we have AC power in our outlets instead of DC power? Explain your answer.
I need to power a 15kw/20HP DC Motor with a rectified 24VDC from a step down transformer with input of 11A and output of 103A/12VAC -24VAC. What is the required Capacitance needed to ensure ripples are cleared and also gives a steady VDC of 24VDC to the DC Motor to run quite well. Please, all note that the rectifier is a full wave rectifier of 100A...
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive The supply voltage is v =300 sinωt , the supply frequency is 50 Hz and the load parameter values are: R =05 Ω, a) Sketch the diagram of electrical circuit b) Sketch the load voltage and current waveforms . c) Calculate the load current d) Calculate the average DC load voltage Vdc . e) Calculate the supply power to the load.
Commercially available strain gages, typically, have nominal resistance of either 120 or 350 Ohm. Discuss the advantages and disadvantages of each type in terms of measurement accuracy/precision and sensitivity.
The ________parameters may not reflect the actual operating conditions but simply provide an indication of the level of each parameter to expect for general use. a.hybrid-pi b.hybrid c.pi d.re