Considered is 20 deg C and a maximum temperature of 30 deg C is designed for, and the modulus of elasticity of steel to be 207,000 Mpa, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.

Considered is 20 deg C and a maximum temperature of 30 deg C is designed for, and the modulus of elasticity of steel to be 207,000 Mpa, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.1P

See similar textbooks

Related questions

Q: the required superelevation is

A: Given data, V= 80 km/hR= 250 m Where, Design is lateral friction is assumed to be fully develop.…

Q: All angles are preferred to measure clockwise because of the graduations of theodolite circle…

Q: 111. For the truss shown in Fig. P-111, calculate the stresses in members CE area of each member is…

A: To find stress in member CE,DE,DF

Q: Using method of joints

A: To find area of member AG,BC,CE

Q: compute the azimuth and bearing of the remaining lines. Draw the figure

A: ###Computation of Azimuth and Bearing of the remaining lines####

Q: Using Area-Moment Method, determine the deflection at the overhanging end in mm. Given: P = 4.2kN…

A: Given data E = 10 GPA = 10 × 103 N/mm2 I = 20 × 106 mm4 Find deflection at overhanging end…

Q: The foreman of the project measures the interior angles of a pentagonal lot and comes out with the…

Q: 16 ft wide sand bed stream (Sf = 0.002, n' = 0.015, with smooth channel banks) has the following…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CD AZIMUTH 225°…

A: Given: Lines Azimuth Distance AB 225o 1200 m BC 346o 1400 m CA - -

Q: Given the figure below, Solve for the following unknowns. RA, MA RB, 40 kN/m = 5m 23 kN/m B…

A: To find support reaction at point A and B

Q: (a) Dry unit weight of borrow pit material. (b) Volume of the finished embankment. (c) Volume of…

Q: many futuristic projection system types, together with their parts and purposes What are they…

A: In order to aid navigators at sea and on land, maps have been created of the trade routes, local…

Q: ection and its location of 65.0×100 mm). 30 kN 15 kN

Q: If d is the distance between equidistant odd ordinates, the Simpson's rule for the areas, is d/2[h1…

A: Given : d distance between ordinate To determine Simpson's rule formula for area calculation

Q: Given the figure below, Solve for the following unknowns. 17 m A 12 m B 35 kN/m 245 KN Determine the…

Q: A simply supported beam 300 mm wide, 500 mm deep and spans 5.1 m supports a service super imposed…

A: L=5.1m d=500-70= 430mm Using Nscp2015

Q: 113. Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…

Q: A and B are two stations Whose coordinates are (585.1 E,1056.9N), (992.7 E,1426.5 N) Find Length and…

Q: forty-foot wooden hull fishing vessel sprang an unexpected leak a few days after leaving port. As…

A: Since an inspection reveals that the bilge was inaccessible, the loss is classified as a…

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CA AZIMUTH 225°…

Q: Irrigation water is to be provided to a crop in a field to bring the moisture content of the soil…

A: Given data: P.W.P=18 %Field capacity=28 %Effective root zone=70 cmDensity of soil, γd=1.3…

Q: A Loose, natural sand deposit has a saturated unit weight of 19.3 kN/m³ and an angle of internal…

Q: 5-27. Determine the reactions acting on the smooth uniform bar, which has a mass of 20 kg.

A: Given : Mass = 20 kg Determine the reaction acting on smooth uniform bar?

Q: A series levelling had been down along the centre line of the proposed road the distance between…

A: St.No BS IS FS HI RL Remarks Elevation After Completion Cut/ Fill A…

Q: A cantilever beam has the cross-section of an isosceles triangle and is loaded as shown below! T1mA…

A: Determine the maximum bending stress in the beam

Q: 4-Classify the following soils using the USCS including Group Symbol and Group Name: Soil % passing…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: A and B are two stations Whose coordinates are (585.1 E,1056.9N), (992.7 E,1426.5 N) Find Length and…

A: Surveying: to determine length and direction of AB

Q: The basketball player likes to release his foul shots with an initial speed vo= 23.5 ft/sec. What 2…

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

Q: If + 0.8% grade meets - 0.7% grade and the rate of change of grade for 30 m distance is 0.05, the…

A: g2 = -0.7% g1 = 0.8% Rate of change of grade r= 0.05/30 = 0.00167

Q: How "Modified Crossflow Dryer" explain the hysteresis in the EMC curve?

A: The moisture content of dry food, which is often a hygroscopic material, is described by EMC data as…

Q: Q4: A. Calculate the pressure of steam at a temperature of 500°C and a density of 24 kg/m³ using (a)…

Q: Traversing Principles: Missing Data Problem 1. A close traverse shows tabulated values of latitudes…

Q: Does the gate AB shown in figure open to the right or left? Gate width equal to 80 cm DI Water Hinge…

Q: answer the following problems using method of joints and method of section separately in solving for…

A: To find stress in member BC,BD,CF

Q: Q1: A simply supported beam and its cross section are shown in Figure. The beam carries a load of…

Q: Q2: The solid rod shown in the Figure has a radius of (20 mm). If it is subjected to the forces of…

Q: 3 kN B 125 mm 2 kN 150 mm 200 mm X

Q: Determine the magnitude of the component force F in Fig. 2-13a and the magnitude of the resultant…

Q: Analyze each of the following structures. Calculate reaction components, and construct shear and…

Q: 11. For the truss shown in Fig. P-111, calculate the stresses in members CE, L DF. The…

A: To find stress in DE,DF,CE

Q: The table below contains the cross- sections Areas of road Calculate the volumes of the earth work…

A: To find volume of earthwork

Q: У L

A: Given:- y=x3-xL To find:- curvature of the beam at themid-span

Q: o:p> Use Horton’s infiltration equation to compute the total infiltrated water (in inch per unit…

Q: Determine the UBC-97 design seismic forces for a nine-story special moment resisting steel frame…

A: Number of floors: 9Structure type: Steel SMRFLocation: NCR (Metropolitan Manila)Distance of building…

Q: The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjected…

A: Data given Height of the pressure tank = 2 m = 2000 mm Internal pressure, P = 2 MPa = 2 N/mm2…

Q: In orthographic projection, the lines of sight are ______ to one another a. always perpendicular…

Q: For the truss shown in Fig. P-111, calculate the stresses in members CE, DE, and DF. The…

A: ###Determination of stresses in Members CE,DE,DF ###Using method of separation ###

Q: A loose compacted sand fill is 1.80 m in depth and has a relative density of 40%. Laboratory tests…

Q: Classify each of the trusses as statically determinate, indeterminate, or unstable externally.…

A: Solution: Check for the determinacy of the truss: Number of members, m = 13 Number of reactions, r =…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Considered is 20 deg Celsius and a maximum temperature of 30 deg Celsius is designed for, and the modulus of elasticity of steel to be 207,000 MPa, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.
Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
(a) List and describe the three failure modes of a steel beam without lateral torsional buckling.Also sketch a diagram of each of the three failure modes to assist with the description of the failuremode. (b) Please define Cb, the moment gradient, and explain how it can increase the resistance of abeam to fail in lateral torsional buckling (LTB) in both the inelastic and elastics LTB ranges. (c) List at least five ways in which you can increase the flexural strength of a steel beam for agiven span
A floor system consisting of 100mm thick concrete slab cast monolithic with continuous T beams of 8m span and on a center-to-center spacing of 1.20m. Web dimensions are bw = 300mm and d = 500mm. The midspan is reinforced with 6-32mm bottom bars and 2-32mm top bars. f'c = 21MPa, fy = 415Mpa. Determine the ultimate bending moment at midspan.
Determine the ultimate moment capacity of the reinforced concrete beam if it is reinforced with tension bars of 6-25mm in two layers. f'c = 20.71 MPa, fy = 414 MPa.
A rectangular reinforced concrete beam 300 x 500 mm (b x d) is provided with 4H20 bar as compression steel. Determine the area of tension steel needed for the beam to attain its full = moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 50mm. Based on the propose design, make a design check
Assuming k = 3000 lb/in2, and considering only the bending stress:What rail type would you recommend if two identical forces of P = 30,000 lb, 70" apart, are applied to it?
1. Three concentrated loads of 50kN, 30KN and 60 kN are loaded on a 14-meter-span fully-restrained beam and each applied at 7 m, 9m and 11 m from the left support respectively. Which of the following most nearly gives the elastic section modulus of the beam (in mm³) if the shape factor is 1.4 and the yield stress is 240 MPa. a.443.667 b. 546.778 c. 488.775 d. 505.952 e. 521.345 2. A W 14 x 68 having the following properties:Prop. of W 14 x 68d = 356.62 mm Sx = 1688 x 10³ mm³ Cb = 1.14bf = 254.89 mm Zx = 1885 x 10³ mm³ Lp = 2.65 mtf = 18.29 mm E = 200000 MPa Lr= 8.05 mFy = 345 MPa Elastic buckling stress: Fcr = 420 MPa Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 12 m. a. 450 b. 709 c. 638 d. 486 e. 585 Which of the ff. most nearly gives the flexural strength of the beam if the beam has an unbraced length of 6 m. a. 585 b. 709 c. 638 d. 450 e. 486
The load over the plate varies linearly along the sides of the plate such that p = (12 - 6x + 4y) kPa. Determine the magnitude of the resultant force and the coordinates (x̄, y̅) of the point where the line of action of the force intersects the plate.
Our University wants to construct a signal post near the entrance, for which they are in need of a horizontal structural element with one end fixed and other end is free. That is to be made up of flexible composite material. The maximum allowable load at free end is 900 kN. The length of the horizontal structural element is 2.2 m. The cross section of the beam is a hollow circular section. Outer diameter 200 mm with wall thickness of 20 mm. Find the deflection at the free end and maximum slope in beam by neglecting self-weight of the diving board. Take Young's Modulus as 170 GPa.
steel joist is spaced at 3’-0” oc and spans 35’-0”. It carries a dead load of 45 psf and a live load of 100 psf. What is the most economical steel joist able to carry this load? a. 24K7 b. 26K7 c. 28K7 d. 30K7
A rectangular reinforced concrete beam 300 x 500 mm (b x d) is provided with 4H20 bar as compression steel. Determine the area of tension steel needed for the beam to attain its full = moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 50mm.