Answered: D d. a° L1 El. Parameter in Dimension…

D d. a° L1 El. Parameter in Dimension in lo: Drawing mm d 35 L1 28 |Cutting speed (Cs) in m/ minute 22 Taper angle "a" in degrees

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Related questions

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

Q: 3. A 50-mm-long, 30-mm-diameter hole in a steel rod is being enlarged in diameter to 31 mm by one…

Q: In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original…

Q: The rpm (N) of the shaft, diameter (d) =25 mm, cutting speed (v) =50 m/min is; O 39.25 O 636.9 O…

A: Given data as per question Diameter of shaft=25 mmcutting speed =50mmincalculating speed of…

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: Note: All dimensions are in mm Ø 34 7. 3.) A 34 mm diameter x 120 mm shafting will be turned using a…

A: Given:- Dinitial=34 mm,Dfinal,Rough=31 mm,Dfinal,Finish=30 mm,L=50 mm,rough turn:-V=30 mmin,depth of…

Q: Q4 Tool life of a turning tool is given by VTO.12xx=C_at a cutting speed (V) of 25m/min, feed(f)…

Q: D.= 0.250" D, = 0.125" %3D L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018…

A: Given:v=211 feet/minf=0.0018 in/revL=6.250 in

Q: in shaft turning Steel raw material, diameter 40 mm., length 200 mm. to obtain a lathe workpiece…

A: Given, D1 = 40 mm L1 = 200 mm D2 = 35 mm L2 = 150 mm Cutting Speed, S = 25 m/min feed rate, f = 0.2…

Q: In a turning operation on stainless steel, cutting speed = 150 m/min, feed = 0.25 mm/rev, and depth…

A: From the given table write the specific energy for cutting stainless steel.

Q: Determine the optimum cutting speed for an operation on a lathe machine using the following…

Q: Figure and table given below shows the design details of a taper turning operation with a cutting…

A: Given data: The cutting speed of the tool is v=22 mmin The feed of the tool is f=0.2 mmrev The depth…

Q: Figure and table given below shows the design details of a taper turning operation with a cutting…

A: Given: cutting speed is 22 m/ minute. feed is 0.2 mm/ revolution. Depth of cut is 0.5 mm.

Q: Problem 2. Turning Consider Step 2 (Turn Shoulder) in machining the flashlight handle (Figure 2).…

Q: ф20 O 25 $10 25 10 45

A: Machining time is given by, T=LfNwhere, L=length of operationf= feed in mm/revN=rpmGiven:V=60…

Q: (USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min,…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3 of first question. Please…

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

Q: If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in /…

A: As the outer and inner diameter is not given so I am assuming it as D0 and Direspectivelya)…

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

Q: In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to…

A: Option b is correct.

Q: A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine…

A: Given data Diameter of work piece = 55 mmLength of work piece = 200 mmFinal diameter = 45 mmCutting…

Q: Figure and table given below shows the design details of a taper turning operation with a cutting…

Q: A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: In a turning operation on cast iron (150 BHN), the cutting speed is 340 ft/min, feed is 0.06 in/rev,…

A: Given data as per question Cutting speed = 340 ft/min Feed =0.06 in/rev Depth of cut =0.05…

Q: Find the machining time, in seconds, and the rate of material removing in mm^3, sec for a turning…

A: Given, Diameter of the workpiece, D=80 mm=0.08 m Length, L=0.12 m Cutting speed, v=80 m/min Depth of…

Q: B/ A rectangular aluminum block is drilled at a depth of 40 mm using a drill that has two cutting…

Q: Low carbon steel having a tensile strength = 300 MPa and a shear strength = 220 MPa is turned at a…

A: Given data ,σyt=300 Mpa ; σys=Tys=220 MpaVc=2.5 ms =150 mminf=0.2 mmrev…

Q: For a certain job, the cost of metal cutting is 7 180 C/V and the cost of tooling is 270C/(TV),…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: QUESTION 1 Calculate the spindie speed in RPM of a lathe turning a 96 milimeter diameter material…

Q: In a machine test, a cutting speed of 100 m/min indicated the tool life as 16 min and a cutting…

A: Given data: The first cutting speed is V1 = 100 m/min. The tool life based on first cutting speed…

Q: The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: 3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a…

A: (a) The feed rate in inch per minute is 15.28 in/min. (b) The cutting time omitting the over travel…

Q: 5) An orthogonal cutting operation is performed using a rake angle of 15°, and having a chip…

Q: Note: All dimensions are in mm A 34 mm diameter x 120 mm shafting will be turned using a lathe to…

A: given: Diameter of the shaft→Di=34 mm Total length of the shaft→Li=120 mm machinable length of…

Q: A.) A cutting operation is performed on a piece of metal. The rake angle of the tool, α, is eight…

Q: (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min,…

A: Given data : stainless steel with hardness = 200 HB cutting speed (v) = 250 m/min feed (f) = 0.3…

Q: The outline of the part in the Figure below is to be profile milled using a 20- mm diameter end mill…

Q: A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 45 mm for an…

A: Turning is a machining process used to decrease the diameter of a workpiece. Turning is done using a…

Q: The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6…

A: Given Data: Rake angle α=20° Depth of cut d=6 mm Feed rate f=0.25mmrev Cutting speed VC=0.6ms Chip…

Q: A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in…

Q: b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm,…

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

Q: AHSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The arameters…

Q: In a turning operation, the workpiece diameter is Dm=44.00 mm and the diameter after the operation…

A: Given:Dm=44 mmDc=22 mmV=15 m/minf=0.03 mm/rev

Q: Q1_Tuming operation carried out on Aluminum shaft with specific energy of 0.7 N.m/mm. Cutting speed…

A: As per our guidelines we are supposed to do only first question, if more than one question asked,…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following. (a) Diameter "D" in mm

d
q°
L1
SI.
Parameter in
Dimension in
No: Drawing
mm
1
d
35
2
L1
28
|Cutting speed (Cs) in m/
minute
22
Taper angle "a" in degrees
4
4.

Expert Solution

Step 1

Step by step

Solved in 2 steps with 2 images

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following data is applicable for a turning operation. The length of job is 900 mm, diameter of job is 200 mm, feed rate is 0.25 mm/rev and optimum cutting speed is 300 m/min. The machining time (in min) is ___. A. 7.539 B. 7.90 C. 8.25 D. 9.00
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: a/Increased b/Decreased c/Maintained the same
In a machine test, a cutting speed of 100 m/min indicated the tool life as 16 min and a cutting speed of 200 m/min indicated the tool life as 4 min. Calculate the values of n and C.
Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b. Unit of feed is in meter per tooth c. Unit of cutting speed is in meter per second d. Unit of feed is millimetre per tooth
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following . (e) Time for single pass "Tfinal" in minutes
In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle  = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work done
Briefly define the term cutting speed.
Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a feed rate of 0.004".
The TPI specified on a print is 0.030". If checking a taper attachment setup with a cross-slide-mounted dial indicator, how much movement should register on the indicator if the carriage is moved 1" in the cutting direction?
Many of the cutters used in machining are made of either __________________ or ____________________.
1.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting speed is _________?(m/min)
22 “Milling is an intermitted cutting operation”. Explain it.