Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b. Unit of feed is in meter per tooth c. Unit of cutting speed is in meter per second d. Unit of feed is millimetre per tooth

Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b. Unit of feed is in meter per tooth c. Unit of cutting speed is in meter per second d. Unit of feed is millimetre per tooth

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.5: Taper Turning

Problem 11RQ: The TPI specified on a print is 0.030". If checking a taper attachment setup with a...

See similar textbooks

Related questions

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

Q: What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm…

A: Given Data N=2409 rpm D=86 mm

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: a. Downward b.…

A: Given :- In Drilling machine, Feed given to drill in this direction makes the hole Select one: a.…

Q: i. spindle rpm ii. feed speed iii. cutting time iv. material removal rate

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is provided to low strength material, to reduce BUE, for low speed operation

Q: :The form milling from the following is

A: Option b is correct.

Q: How long will it take to drill a hole through a 10 cm thick steel plate if the drill feed is 0.1 mm…

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

Q: Name the following cutters and its function.

Q: Systematize the following operations in a rising sequence of their cutting speeds. (a) Turning (b)…

A: Cutting is used to cutting the material according to the desired conditions or we can say that…

Q: The angle of forst of c

A: Given; From given figure: A stepped shaft subjected to a twisting moment applied at BShear modulus…

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: O a. 45 degree…

A: Drilling is a cutting operation in which a drill bit is used to cut a circular hole in a solid…

Q: The tool signature of a single point cutting tool in ORS system is 10° – 15° - 20° – 15° – 30° – 60°…

Q: )Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given d=22mm=0.022m spindle speed N=210rpm

Q: Read the sentences given below and Identify the wrong statement. Sentence 1. The advantage of an…

A: Sentence 1. The advantage of an independent chuck is that the work can be centered to high…

Q: From the following Identify cutting tool made by forging before hardening and grinding. О а. Ob. О…

A: First step for making a tool is

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 186.00 m/min and…

A: Find the spindle speed Cutting speed = 186 m/sec External diameter = 38.50 mm

Q: State the equations used to calculate: (a) The rotational speed in rpm b) The feed rate in in/min.…

A: In machining process There is requirement of calculation (a) The rotational speed in rpmb) The…

Q: The figure shows operation of drilling machine Tool feeds O a. Drilling O b. Boring O c. Reaming O…

Q: During Milling machining the rate of material removal and surface finish determines the following…

Q: Answer the following questions by circling True or False. 13. The cutting speed of the hydraulic…

A: As per Bartleby guideline we are allow to give answer of one question at a time so please post other…

Q: Up milling operation, the work is feed in the same direction the rotation of the cutter.…

A: Basics of Upmilling & Downmilling.

Q: A cutting tool has a radius of 1.8 mm. The feed rate for a theoretical surface roughness of is 5 Hm…

A: The nose radius of the tool is given as, R=1.8 mm. Now convert the units of surface roughness from…

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: Give at least 5 purpose of cutting internal threads by the use of Lathe Machine

A: given; Give at least 5 purpose of cutting internal threads by the use of Lathe Machine.

Q: Define; (a) Cut-in speed, (b) Cut-out speed, and (c) Betz limit

A: (a) Cut-in speed It is defined as a minimum speed at which the turbine starts generating…

Q: 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

Q: Increasing the cutting speed (Vc) affects the surface finish by:

A: The dimensional accuracy of the final product depends on the cutting speed.

Q: Drilling operation to produce conical shape on a drilled hole is known as a. Boring b. Counter…

Q: 9q ___________________ is the lathe operation, which is performed without the cutting tool…

A: For thread cutting, the tool post has to move automatically based on setting of gear box. Boring is…

Q: 12. What must be the cutting speed of two inches milling cutter if it has to machine a piece of mild…

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: 10. Formula for cutting speed of the shaper, tell the meaning of each variables.

A: SHAPER In shaping, the cutting tool is held in the tool post located in the ram, which reciprocates…

Q: 5. According to the figures as follows, please point out: 1) Gear hobbing cutter is , Milling cutter…

A: Note: We know that, for the gear hobbing process, the cutter is rotating in the axis perpendicular…

Q: The outline of the part in the Figure below is to be profile milled using a 20- mm diameter end mill…

Q: A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with…

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

Q: size of

A: the solution of above question is below.

Q: A milling cutter having 8 teeth is rotating at 150 rpm. If the feed per tooth is 0.1 mm, the speed…

A: Given: Teeth on milling cutter= 8 Speed of cutter, N=150 rpm Feed per tooth= 0.1 mm

Q: QUESTION 12 How long would it take a turn 6 inches of 1-inch bar stock on a No. 3W. and S. turret…

A: This is the very basic question of machining time calculation on lathe.

Q: From the following Identify cutting tool made by forging before hardening and grinding. O a. O b.…

A: Cutting tool made by forging before hardening and grinding is called tipped tool

Q: the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min…

A: Given, L = 120 mm d = 35 mm V = 30 m/min f = 0.7 mm/rev

Q: total drill time in seconds is

A: Given data; In a single pass drilling operation,Hole oil diameter,d=15 mmDrilled in a steel plate…

Q: From the following Identify cutting tool that has the cutting edge in the form of small tip made of…

A: Let us discuss about about given single point cutting tool

Q: Milling is an intermitted cutting operation”. Explain it.

A: A milling machine is a machine tool that cuts metal as the workpiece is fed against a rotating…

Q: 12. The following is concerned with the depth of the hole: * Drilling operation Drilling operation…

A: Blind-hole is defined as the a hole that is drilled or reamed to a certain depth without going…

Q: 1- Which one of the following operation is not related to drilling? a) Threading b) Counter boring…

A: The correct option to the above question is Option (a). The threading is related to the cutting of…

Q: process used for cutting a gear on a milling machine is called The a. Gear forming b. Gear shaping…

A: Option c is correct

Q: i) it is rotated

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Briefly define the term cutting speed.
Many of the cutters used in machining are made of either __________________ or ____________________.
Systematize the following operations in a rising sequence of their cutting speeds. (a) Turning (b) Grinding (c) Drilling (d) Milling
1.To mill material having a cutting speed of 40 fpm. What should be the RPM of 1.25 inches diameter cutter. 2. Give the RPM of a 5 inches cutter. Material, cold drawn steel having A cutting speed of 100 fpm.
In a milling machine the distance the workpiece advances under the cutter is known as Select one: a Cutting speed b. Thickness c Depth of cut d. Feed
In a multi point cutting tool the positive rake angle is used to cut low tensile strength and non-ferrous metals. Select one: True False
Suppose you need to drill a 5/8 inch hole, but the set of drill bits is measured in sixteenths of an inch. What size drill bit should you use?
Question two a.Define the following terms. State the appropriate SI units i)Cutting speedii)Cutting feediii)Material remova rateb.A hole is to be driled in a steel plate of thickness 12mm at a feed of 0.35mm/rev and a spindle speed of 750 rpm. Calculate the i)Material remova rateii)Time taken to complete the process
A______ can be used to measure cutting fluid concentrations.
What unit of measure is used to define cutting speeds?
The TPI specified on a print is 0.030". If checking a taper attachment setup with a cross-slide-mounted dial indicator, how much movement should register on the indicator if the carriage is moved 1" in the cutting direction?
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=