D. 5.: Choose the correct answer A. A 900 kg car cruising at a constant speed of 60 km/h is to be accelerate to 100 km/h in 4 s. The additional power needed to achieve this acceleration is: iii. 62 kW i. 222 kW ii. 90 kW iv. 56 kW v. 2.5 kW B. Water is boiling at 1 atm pressure in a stainless steel pan on an electric range. It is observed that 2 kg of liquid water evaporates in 30 min. The rate of heat transfer to the water is: iv. 2.32 kW v. 0.47 kW iii. 2.51 kW i. 3.12 kW ii. 2.97 kW

D. 5.: Choose the correct answer A. A 900 kg car cruising at a constant speed of 60 km/h is to be accelerate to 100 km/h in 4 s. The additional power needed to achieve this acceleration is: iii. 62 kW i. 222 kW ii. 90 kW iv. 56 kW v. 2.5 kW B. Water is boiling at 1 atm pressure in a stainless steel pan on an electric range. It is observed that 2 kg of liquid water evaporates in 30 min. The rate of heat transfer to the water is: iv. 2.32 kW v. 0.47 kW iii. 2.51 kW i. 3.12 kW ii. 2.97 kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a.Which of the following appropriately describes the pumping energy efficiency when a pump is transferring water150 l/s (liters per second) with 1 bar pressure difference and the power consumption is 21 kW? 1.59 % 2.140kW/s 3.21kW /bar 4.39 Wh/m
Steam enters a turbine with a pressure = 4,786 kPa and h 3,204.99 kJ/kg, with a flow of 7.383 kg/s. Steam leaves with h = 2,344 kJ/kg and pressure of 23 kPa. The radiative heat loss is equal to 27.18 kJ/kg of steam. Determine the work steady flow in kW. Answer must be in 3 decimals.
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
2)A)What is convection in Heat Transfer ? B)Does the convection affect the lifetime of the turbine? C)How does the convection affect the lifetime of the turbine?
A sewage aeration blower running at 3,500 rpm is designed to deliver 34,000 m3/hr of air from 20°C and 1.03 kg/cm2 atmospheric pressure to a discharge pressure of 1.56 kg/cm2 with an efficiency of 70%. On a hot summer day, the atmospheric temperature rises to 43°C but the barometric pressure does not change. It is desired to vary the blower speed to maintain the same discharge pressure. Determine the blower speed, in RPM, for the summer operation.Determine the Brake Horsepower required, assuming that the efficiency remains constant and assume a mechanical efficiency of 0.9 (k = 1.4 for air).Determine corresponding flow in nominal meter cube per hour.
A sewage aeration blower running at 3,500 rpm is designed to deliver 34,000 m3/hr of air from 20°C and 1.03 kg/cm2 atmospheric pressure to a discharge pressure of 1.56 kg/cm2 with an efficiency of 70%. On a hot summer day, the atmospheric temperature rises to 43°C but the barometric pressure does not change. It is desired to vary the blower speed to maintain the same discharge pressure. Determine the blower speed, in RPM, for the summer operation. Determine corresponding flow in nominal meter cube per hour. Determine the Brake Horsepower required, assuming that the efficiency remains constant and assume a mechanical efficiency of 0.9 (k = 1.4 for air).
Steam enters a turbine with a pressure 4,229 kPa and h=3,263.08 kJ/kg, with a flow of 7.397 kg/s Steam leaves with h= 2,337 kJ/kg and pressure of 22 kPa. The radiative heat loss is equal to 20.86 kJ/kg of steam Determine the work steady flow in KW. Answer in 3 decimal places.
Book - Advance Energy Systems, 2ed, Khartchenko
Water is pumped from a 200-ft-deep well into a 100-ft-high storage tank. Determine the power, in kW, that would be required to pump 200 gal/min.
Three hundred sixty kilojoules of heat is transferred from a hot source of T = 600 K to a cold sink of T = 250 K. Determine the total work lost if Tsurr = 300 K
DESCRIBE THE ENERGY ANALYSIS OF STEADY-FLOW SYSTEMS
This question related to thermodynamics