Solve the following. (d, e, f) only. Directions: Solve the following problems and show your solution.1. Consider the circuit below. Solve for the following, (in a simple way of solving)a. Total Resistanceb. Voltage between point A & B.c. Current Totald. Current Il and I2e. Power across R1, R2 and R3f. Power delivered by the sourceR, = 2.2 k.AV, = 15 VR = 3.3 knR= 680 N

This question belongs to network theory . It is based on current division rule , kirchhoff's…

Answered: d. Current Il and 12 e. Power across…

Engineering

Electrical Engineering

d. Current Il and 12 e. Power across R1, R2 and R3 f. Power delivered by the source

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the circuit diagram below. The circuit supplies power to the unknownresistive load, L. Determine the Thevenin equivalent circuit for the supply circuit.Verify that your Thevenin equivalent is indeed equivalent to the original circuitby simulating both circuits using CircuitJS and reporting the load current in each.Attach an exported image or screen shot of both of your circuits from CircuitJSwith the current and voltage “shown” (colors are shown on the diagram).
For the bridge circuit shown below, consider it R1 = 4Ω, R2 = 6Ω, R3 = 2Ω, is R4 = 7Ω, 55 = 5Ω, and calculate the following: a) The current flowing in each resistor. b) The equivalent resistance of the circuit across the battery.
Consider the following circuit where V1 = 22 V, I1 = 2 A, R1 = 17 Ω, R2 = 5 Ω, R3 = 8 Ω, R4 = 9 Ω , How much is Norton's resistance?
1. Which resistance(s) has no effect on the value of vo? a. 4 ohms b. 260 ohms c. 16 and 260 ohms d. 40 ohms 2. What is the short circuit current (in amperes) when solving for the Thevenin equivalent circuit as seen by the 250Ω resistor? 3.Using superposition to get the Thevenin voltage (in volts) seen by the 250Ω resistor, what is the contribution by the 1A source?
Construct this circuit using the simulation: (simulation link: https://phet.colorado.edu/sims/html/circuit-construction-kit-dc/latest/circuit-construction-kit-dc_en.html ) Let: R1 = 2000 ohms R2 = 5000 ohms R3 = 3000 ohms R4 = 1000 ohms V1=24V 1. Total equivalent resistance of the circuit (using theoretical calculation) 2. Total current on the circuit (using simulation) 3. Total equivalent resistance of the circuit (using simulation) 4. % Error of #1 and #3 question.
1. Draw the Norton equivalent for the circuit given. For the looking back Resistance, Ro (express your answer in 2 decimals): Ro= ____ kΩ
Design a circuit that will have an outcome of the highest equivalent resistance across the terminals with a 30Vdc source. Given that the R1 = 10 R2 = 50 R3 = 85. Determine the equivalent resistance from the combination of resistors, R123, R12, R23, and R1.
A DC resistive circuit includes a 5.5 mA current source, Is, which is connected to 2 resistors in parallel: Ry which is 7 kQ and R2 which has 1.75 times more conductance than R1. There is a closed switch before R2 in series with only this resistor. The negative terminal of the current source is at ground. a) Draw the circuit diagram for the above described circuit being sure to label all circuit elements, current directions and voltage polarities of each element. b) The switch is now open. Redraw the circuit diagram with a voltmeter which measures the voltage across the resistor Ry. Be sure to label all circuit elements, current directions and voltage polarities of each element. Indicate the value displayed by the voltmeter.
The table in (a) gives the relationship between the terminal current and voltage of the practical constant current source shown in (b). 1. Plot is versus vs.2. Construct a circuit model of this current source that is valid for0≤vs≤30 V, based on the equation of the line plotted in (a).3. Use your circuit model to predict the current delivered to a 3 kΩresistor.4. Use your circuit model to predict the open- circuit voltage of thecurrent source.5. What is the actual open-circuit voltage?6. Explain why the answers to (d) and (e) are not the same.
find the following using the attached picture: (a) Calculate the equivalent resistance of this circuit. (b) Calculate the following quantities:1). current through R52). current through R33). voltage across R1 (c) To measure the current flow though R1 and the voltage onR5, how should we connect the ammeter and voltmeter?Draw a circuit diagram showing your answer. (d) What is the ideal impedance of1). an ammeter?2). a voltmeter?
Calculate the currents (,,i1, i2, i3 and ly in the figure below. Then, obtain the voltage value on each resistor in the circuit. Solve the question using the mesh current method
A 30-volt source battery is connected in series with the 6-load resistors namely 1 ohm, 2 ohms, 3 ohms, R ohms, 5 ohms, and 6 ohms respectively. If the total power is 30 watts, find the value of R in resistance and its current drawn as well as the total resistance (a) provide solution (b) provide circuit diagram