With reference to the attached example. Apply dimensinal analysis to show that all values/units used are homogeneous. Data has been gathered from a lifting system used to transport engine parts. The system consistsof a drum and cable. The following data was obtained when the drum lowers the load (assumeconstant acceleration).Drum diameter = 0.8mMass of load = 3kgInitial velocity = 0 m/sTime to descend = 0.5 secsDistance travelled = 0.25mYou have been asked to use this information to determine:a) The final linear velocity of the loadb) The linear acceleration of the loadc) The final angular velocity of the drumd) The angular acceleration of the drume) The tension force in the cablef) The torque applied to the drumDrumCableLoadIn determining the above quantities, you should clearly state the formulae used and applydimensional analysis techniques to show that all values/units used are homogeneous.From the formulae used (above) you should apply dimensional analysis techniques to develop twoequations for power (in terms of linear velocity and angular velocity).

Given, Initial velocity, u= 0m/s distance travelled, s= 0.25 m Time to descend, t= 0.5 s Mass of…

Data has been gathered from a lifting system used to transport engine parts. The system consists of a drum and cable. The following data was obtained when the drum lowers the load (assume Constant acceleration). Drum diameter = 0.8m Mass of load = 3kg initial velocity = 0 m/s Time to descend = 0.5 secs Distance travelled = 0.25m Drum

Data has been gathered from a lifting system used to transport engine parts. The system consists of a drum and cable. The following data was obtained when the drum lowers the load (assume Constant acceleration). Drum diameter = 0.8m Mass of load = 3kg initial velocity = 0 m/s Time to descend = 0.5 secs Distance travelled = 0.25m Drum

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

As a mechanical engineer, you can predict the performance of a new centrifugal pump using two methods which are One Dimensional Analysis (Velocity Triangle) and Hydraulic Scaling. Describe the limitation of each method.
Consider steady flow of air through the diffuser portion of a wind tunnel. Along the centerline of the diffuser, the air speed decreases from uentrance to uexit as sketched. Measurements reveal that the centerline air speed decreases parabolically through the diffuser. Write an equation for centerline speed u(x), based on the parameters given here, from x = 0 to x = L.
Consider steady flow of water through an axisymmetric garden hose nozzle. Along the centerline of the nozzle, the water speed increases from uentrance to uexit as sketched. Measurements reveal that the centerline water speed increases parabolically through the nozzle. Write an equation for centerline speed u(x), based on the parameters given here, from x = 0 to x = L
Fluid mechanics (Subject) Write legibly and sole neatly, show diagrams A surface vessel is 156 m long and moves at a velocity of 6.83 m/s. Determine the velocity of a geometrically similar model 2.44 m long be tested.a. velocity : ____________________ m/s
Unless stated otherwise take:Patm = 10^5, P(water) = 1000 kg/m^3 ; P(air) = 1.2 kg/m^3 ; g = 9.8m/s^2gage pressure Pg = P - PatmUnless specified otherwise assume uniform velocity profiles in duct locations.The Bernoulli eq’n (BE), P + ½ρV2 + ρgz = constant In this formulation the scalar variable z is the vertical height measured opposite the direction of g (z is always taken up independent of your coordinate system; pgz is potential energy)This BE is only valid along a streamline in steady state flow, when viscous friction effects can be ignored, called “ideal” fluid motion, and the density is assumed to be constantthe differential radial component of –?P + ρg = ρawith the centripetal acceleration , ar = - V^2/r , to get dp/dr = ρgr + ρV^2/rThe Bernoulli eq’n is often divided through by the constant ρg ≡ γ so that each term has units of length, a height or “head” : (P/ ρg) + (V2/2g) + (z) = constant. Q = VA = flow rate = constant, as a second eq’n to solve for an unknown velocity. the…
A prototype ocean platform piling is expected to encountercurrents of 150 cm/s and waves of 12-s period and 3-mheight. If a one-fifteenth-scale model is tested in a wavethe channel, what current speed, wave period, and wave heightshould be encountered by the model?
Some students want to visualize flow over a spinning baseball. Their fluids laboratory has a nice water tunnel into which they can inject multicolored dye streaklines, so they decide to test a spinning baseball in the water tunnel. Similarity requires that they match both the Rey n olds number and the Strouhal number between their model test and the actual baseball that moves through the air at 90 mi/h and spins at 300 rpm. Both the air and the water are at 68°F. At what speed should they run the water in the water tunnel, and at what rpm should they spin their baseball?
Given the pump(or fan) characteristics in tabular form of up to 20 points of head, η, and flow rate Q. Using EES program or any other software, draw the pump(or fan) characteristic curves, and the system characteristic ( in the form Es= Δz+kQ²) requiring Δz and k input. The program will enable the user to alter the pump (or fan) and system characteristics (Δz and k) to obtain the new curves and establish the operating point.
Books on porous media and atomization claim that the viscosityμ and surface tension Y of a fl uid can be combinedwith a characteristic velocity U to form an important dimensionlessparameter. ( a ) Verify that this is so. ( b ) Evaluatethis parameter for water at 20°C and a velocity of3.5 cm/s. Note: You get extra credit if you know the nameof this parameter.
A tidal estuary is dominated by the semidiurnal lunar tide,with a period of 12.42 h. If a 1 : 500 model of the estuary istested, what should be the model tidal period?( a ) 4.0 s, ( b ) 1.5 min, ( c ) 17 min, ( d ) 33 min, ( e ) 64 min
The power P generated by a certain windmill design dependson its diameter D , the air density ρ , the wind velocity V , therotation rate Ω , and the number of blades n . ( a ) Write this relationship in dimensionless form. A model windmill, of diameter50 cm, develops 2.7 kW at sea level when V = 40 m/s andwhen rotating at 4800 r/min. ( b ) What power will be developedby a geometrically and dynamically similar prototype, ofdiameter 5 m, in winds of 12 m/s at 2000 m standard altitude?( c ) What is the appropriate rotation rate of the prototype?
Suppose that it is desired to estimate volume fl ow Q in apipe by measuring the axial velocity u ( r ) at specifi c points.For cost reasons only three measuring points are to be used.What are the best radii selections for these three points?