Define stress, normal stress, shear stress, and pressure.

Q: What is inclined plane?

A: Given; Define the inclined plane and its use,  with two examples where it is used ?

Q: calculate the pressure at the bottom of the Mariana Trench, which has a depth of roughly 11,000…

A: The Pressure at a depth inside a fluid is given as  P=ρghHereρ is the density of the fluidg is the…

Q: 1. When a load of 1.2 x 10^6 N is placed on a battleship, the ship sinks 3.5 cm in the water. what…

A:

Q: What is the third kind of stress-strain situation?

A:

Q: Critical stress value needed to initiate plastic deformation is elastic deformation. Yes No

A: By stress-strain curve, A material is considered as an elastic material when stress is proportional…

Q: Explain the graph below. t, eirs с. Elastic Plastic deformation Fracture point E H Linear 0 <1% 30%…

A: Stress is the force acting on the material per unit area of the material. It is denoted by σ. It is…

Q: The distortion of the earth's crust is an example of sheer on a large scale. A particular rock has a…

A: Write the shear strain. ϕ=tanϕ=∆xh=∆x3000

Q: A vertebra is subjected to a shearing force of 581 N. Find the shear deformation, taking the…

A: Write the given values with the suitable variables. F=581 Nh=8.99 cm=0.0899 md=4.14 cm=0.0414 m…

Q: that

A: If the force applied is high then the pressure will be high on the system. The pressure is inversely…

Q: The tank-pipe system shown in the following figure is to deliver at least 15 m/hr of water. The tank…

A: SOlution: given that Q =  15 m3/hr L = 4 m d = 3 cm = 0.03 m

Q: Stress, Strain, Elastic Deformation, Plastic Deformation, Tensional Stress

A: Since you have asked multiple subparts, we will solve the first three for you. If you want a…

Q: how to calculate average pressure given surface area= 2.73*10-2, mass=22.8 kg, and density is…

A: Given:Mass = 22.8 kgSurface area = 2.73 X 10-2 m2Density = 7.85 X 103 kg/m3

Q: What is difference bw stress and pressure?

A: Following are the points of difference : i) Stress is defined as the amount of force exerted on unit…

Q: What is surface tension? Describe how surface tension in water is useful for plants and animals

A: Molecular in between the fluid is attracted by the other molecules equally in all the direction so…

Q: What relation exists between cross sectional area and velocity of fluid? Velocity and pressure?

A:

Q: Define stress. What is normal and tagential stress?

A: Stress is the measure of body’s reaction to any change, the reaction can be physical.

Q: Hydraulic gradient h -h2 Figure 10.11 h, is the elevation of the water table in well #1, h, is the…

A: Given Data : The height of the well 1 is given as h1 = 506ft. The height of the well 2 is given as…

Q: Calculate the value of force Pressure=10 N/m2 Area=2 m2

A: Given, Pressure = 10 N/m2 Area = 2 m2 Force = Pressure × Area

Q: Explain the principle of stress and follow that up with a diagram and a derivation. Give an example…

A: In this question we have to explain the principle of stress and follow that up with a diagram and a…

Q: For the conditions of the hure, what are the values of (alA and the volume flow rate

A:

Q: When you dive to a depth of 12.50 ft in seawater, what is the pressure?

A: Givendepth (h)=12.50 ft=3.81 mlet p= pressure at depth 12.5 ft

Q: What is viscosity? What is the cause of it in liquids and in gases? Do liquids or gases have higher…

A: Given: viscosity

Q: Describe the different pressure measuring instruments?

A: Instruments which is use to measure and display pressure in an integral unit is called pressure…

Q: Explain different type of stress.

A: There are two types of stress.Normal Stress : Caused due to normal forces (forces perpendicular to…

Q: Define laminar flow and turbulent flow.

A: Laminar Flow:   Laminar flow is a category of flow classified on the basis of different parameters…

Q: 10 kip 5 kip 3 kip

A:

Q: What is elastic fatigue?

A: Step 1An object which is able to resume its normal shape spontaneously after being stretched or…

Q: Differentiate between stress and strain.

A: Stress: - It is defined as the resistive force per unit area that rigid body exerts against an…

Q: 11. Calculate the depth of the Ocean (in meters) at which the pressure is 3 times atmospheric…

A:

Q: A metal plate of area 2.5x10^-4 m^2 is placed on a 0.25×10^-3 m thick layer of castor oil. If a…

A:

Q: Differentiate between stress and strain? Give some examples of each?

A: Stress and strain are two very important factors for the study of strength of materials. With the…

Q: Which statement/s is/are true about deformation? A It is only defined by elastic deformation. It is…

A: Option A is incorrect, there are deformations other than elastic, for example ,plastic deformation.…

Q: Explain the concept of Constant Thrust ?

A:

Q: Which of the following represents a sketch of terminal speed vs. viscosity of the liquid for…

A:

Q: "There are 3 main types of stress .....

A: There are three main types of main stress - 1) Tensile stress 2) Compressive stress 3) shear stress…

Q: What is cause of surface tension?

A:

Q: What is shear modulus?

A:

Q: How does pressure change with depth in a water column?

A: Pressure at a depth P=WA=ρgVA=ρgh

Q: Explain Hooke’s law using graphical representation between deformation and applied force.

A: Hooke's law is applicable to the elastic material and states that extension or compression increases…