Describe and explain the effect(s) on your result for the following possible experimental errors. In each case, specify the component(s) whose percentage(s) would be too high or too low and explain your rationale why these would be changed. (a) After adding DCM to the counterfeit pharmaceutical at the beginning, you didn’t stir or shake the mixture before filtering. (b) Washing the sucrose recovered during the first vacuum filtration with water rather than DCM. (c) During the NaHCO3 extraction, you failed to mix the organic and aqueous layers thoroughly. (d) You mistakenly extracted the DCM solution with 5% HCl rather than 5% NaHCO3. (e) You neutralised the NaHCO3 solution to pH7 rather than pH2.

Describe and explain the effect(s) on your result for the following possible experimental errors. In each case, specify the component(s) whose percentage(s) would be too high or too low and explain your rationale why these would be changed. (a) After adding DCM to the counterfeit pharmaceutical at the beginning, you didn’t stir or shake the mixture before filtering. (b) Washing the sucrose recovered during the first vacuum filtration with water rather than DCM. (c) During the NaHCO3 extraction, you failed to mix the organic and aqueous layers thoroughly. (d) You mistakenly extracted the DCM solution with 5% HCl rather than 5% NaHCO3. (e) You neutralised the NaHCO3 solution to pH7 rather than pH2.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter91: Gas Chromatography

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Briefly explain why should the flask be stoppered after the addition of KI in the standardization of sodium thiosulfate VS.
Describe and explain the effect(s) on your result for the following possible experimental errors. In each case, specify the component(s) whose percentage(s) would be too high or too low and explain your rationale why these would be changed. (a) After adding DCM to the counterfeit pharmaceutical at the beginning, you didn’t stir or shake the mixture before filtering. (b) Washing the sucrose recovered during the first vacuum filtration with water rather than DCM. (c) During the NaHCO3 extraction, you failed to mix the organic and aqueous layers thoroughly. - B (d) You mistakenly extracted the DCM solution with 5% HCl rather than 5% NaHCO3. (e) You neutralised the NaHCO3 solution to pH7 rather than pH2.
Cis-3-hexene and trans-3-hexene can be separated and analyzed using GC without injecting an equimolar standard to a high accuracy. Explain why that is the case for these two compounds while we had to inject an equimolar solution for our experiment
present an experimental design on the separation of components of the mixture of benzoic acid and benzaldehyde. Provide a paragrap of your designed experiment and a schematic diagram of the step-by-step procedure
Based on the resulting chromatograms after visualization with iodine vapor, which between the solvent systems WHITE and MIX resulted in a more effective separation of the pigments of the indigo extract? Explain your answer in terms of the solvent that did not effectively separate the components of the root extract.
Explain the function of using dichloromethane after the steam extraction of Eugenol. Also discuss if there are any differences and which ones in soxhlet extraction and steam drag.
In addition to a low boiling point and immiscibility with water, why is density important to consider in the selection of an extraction solvent? Would an organic liquid with a density of 1.006 g/mL make a good extraction solvent? Explain.Write the chemical reaction that took place during this experiment.
RECRYSTALLIZATION & DECOLORIZATION (Organic Chemistry) 1. Propose a process or procedure by which the purity of re-crystallized benzoic acid can be proven. 2. If you are to account for the three components of the original mixture, considering that they were separated, in what form or state, and where were they after the whole process?
Propose an experimental design on the separation of components of the mixture of o-nitrophenol and p-nitrophenol., provide a schematic diagram of the step-by-step procedure
In the experiment borohydride reduction , using 2.0g of benzophenone, a student obtained 1.6g of filtered material. Calculate the percentage yield and comment on whether this represents the true yield of the reaction product diphenylmethanol.
A student doing this experiment had some problems with the procedure, as described below. Explain what effect each problem would have had on the magnitude of the results calculated. b) The student neglected to open the pinch clamp on the plastic tubing between the filter flask and the beaker when the Mg came in contact with the HCl solution. After the stopper popped out of the Erlenmeyer flask, the student quickly replaced the stopper, opened the clamp, and proceeded with the experiment. c) The student began titrating the unreacted HCl with standard NaOH solution and realized that there was a large air bubble in the buret tip. The bubble came out as the first few milliliters of titrant were added. d) The student forgot to add indicator to the titration mixture until 12.50 mL of titrant had been added. When the indicator was finally added, the solution was colorless.
What is the main drawback of using steam distillation in the isolation of volatile oils from its matrix?