Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW at 720 r.p.m. The following permissible stresses may be used : Permissible shear stress for shaft, bolt and key material = 33 MPa Permissible crushing stress for bolt and key material = 60 MPa Permissible shear stress for the cast iron = 15 MPa

Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW at 720 r.p.m. The following permissible stresses may be used : Permissible shear stress for shaft, bolt and key material = 33 MPa Permissible crushing stress for bolt and key material = 60 MPa Permissible shear stress for the cast iron = 15 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Solve the preceding problem for a welded Tank with a = 62°,r = 19 irM = 0.65 in.,p = 240 psu E = 30 X 106 psi, and v = 0.30
4. Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW at 720 r.p.m. The following permissible stresses may be used: Permissible shear stress for shaft, bolt and key material 33 MPa Permissible crushing stress for bolt and key material = 60 MPa Permissible shear stress for the cast iron = 15 MPa
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Design a muff coupling to connect two shafts transmitting 40 kW at 120 r.p.m. The permissibleshear and crushing stress for the shaft and key material (mild steel) are 30 MPa and 80 MParespectively. The material of muff is cast iron with permissible shear stress of 15 MPa. Assumethat the maximum torque transmitted is 25 per cent greater than the mean torque
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
7. Design a muff coupling for joining shafts transmitting 8 kW at 400 rpm. The shaft and the key are made of steel with 45 MPa and 80 MPa allowable stresses in shear and crushing, respectively. The material of the sleeve is CI, with allowable shear stress 10 MPa. Service factor KS =1.2.
2. Design a muff coupling to connect two shafts transmitting 40 kW at 120 r.p.m. The permissible shear and crushing stress for the shaft and key material (mild steel) are 30 MPa and 80 MPa respectively. The material of muff is cast iron with permissible shear stress of 15 MPa. Assume that the maximum torque transmitted is 25 per cent greater than the mean torque
A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150mm. the shaft may be subjected to either a direct tensile load of 400kN or a twisting moment of 18kN-m. if the maximum direct and shearing stress permissible in the bolt material are 125MPa and 55MPa respectively, find the minimum diameter of the bolt required.
A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040 steel on a 7” bolt circle. The shafts runs at 300 rpm and transmits 45 hp. Assume a factor of safety of 5, ultimate tension of 70,000 psi, and ultimate shear of 55,000 psi. Determine: a) The torque transmitted, in-lbs b) The force applied per bolt, lbs c) The diameter of the bolt required, in d) The thickness of flanged to be used, in
Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in lb-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?
A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150 mm. The shaft may be subjected to either a direct tensile load of 400 kN or a twisting moment of 18 kN·m. If the maximum direct and shearing stresses permissible in the bolt material are 125 MPa and 55 MPa respectively. Find the minimum diameter of the bolt required. Assume that each bolt takes an equal share of the load or torque.