i need the answer quickly In the following electrohydraulic system. Sketch the system again, and write thename of each part, explain the working procedure of the system, where is theinput port and output port ?. Explain the electrohydraulic controller, what is themost advantages of the system and where it is used, Show on the sketch.VALVE PLATETILTING BOX CONTROLTILTING BOXCYLINDER BARRELTRUNNIONPISTONFSOCKET RING8-ENDCYLINDER BARREL(HYDRAULIC MOTOR)PISTONRODSOCKET RINGA-ENDDRIVESHAFT

This phrase refers to any combination of hydraulic drives and electrical (electronic) signal…

n the following electrohydraulic system. Sketch the system again, and write the ame of each part, explain the working procedure of the system, where is the nput port and output port ?. Explain the electrohydraulic controller, what is the nost advantages of the system and where it is used, Show on the sketch.

n the following electrohydraulic system. Sketch the system again, and write the ame of each part, explain the working procedure of the system, where is the nput port and output port ?. Explain the electrohydraulic controller, what is the nost advantages of the system and where it is used, Show on the sketch.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter16: Advanced Automatic Controls-direct Digital Controls (ddcs) And Pneumatics

Section: Chapter Questions

Problem 3RQ: One advantage of a modern control system is A. simplicity. B. faster response. C. ability to...

See similar textbooks

Similar questions

) Explain the procedure adopted to arrive at the specification of piezo electric sensor charge amplifiercrank angle encoder and AD convener with data storage for heat release analysis of a given IC engine. (b) Discuss the method of obtaining pressure crank angle diagram. List down the parameters that can bestudied from the pressure crank angle diagram.
I am not entirly sure what system this problem is decribing. what do the fbd's for this look like?
Discuss the effect of operating conditions on performance of SSS-VCRS with the help of p-h diagram
What are the two initial conditions which must be formulated for a SDOF system?
Based on the pic attached, If component B of #6 is changed to 3 parallel components and each has thesame reliability, what is the system reliability now? pls provide celaar solutions detailed thanks
The automatic washing machine system is an example of ........... loop system.
a.explain how a flyball governor works and its relationship to control system. b.Give two practical and personal experience which you have encountered which is considered to be a control system.Give one example for each open loop systems and closed loop systems
Q. Based on pneumatic components given in Figure 1, construct one cascade circuit using two air-line concept to move double acting cylinders A and B with process sequence A+B+B−A− . Answer must include the time ladder diagram, cylinder group and output group.
INSTRUCTION: This is a topic for Pneumatic Controls Engineering. You may use Fluidsim to illustrate the solution (circuit diagram) to the given problem. Please refer to the problem below and apply the appropriate pneumatic system circuit. PROBLEM: The prototype of a pneumatic domestic rubbish compactor (under table model) is operated with a maximum working pressure of p = 3bar = 300 kPa. It is equipped with a pre-compactor (1A) including glass crusher as well as a main compactor (2A), which exerts a maximum force of F = 2200 N. When a start button is pressed, first the pre-compactor advances, then followed by the main compactor. The subsequent return stroke of both double-acting cylinders takes place simultaneously. In the event that the main compactor does not reach the forward end position — rubbish bins full —, the return stroke of both cylinders is initiated by a pressure sequence valve. It is set to switch at p = 2.8 bar = 280 kPa.
One advantage of a modern control system is A. simplicity. B. faster response. C. ability to modulate. D. that they are less expensive.
What are the types of noise suppresion? Describe each type.
Hello Sir.Good Evening. I'm currently taking an exam Control System Lesso I have a question related Control System Lesson. The following below is my question.Please advise fast, Thank you so much.