(a) What value of filter capacitor is required to produce a 1% ripple factor for a full-wave rectifier having a load resistance of 1.5 KN. Assume the rectifier produces a peak output of 18 V. (b) Determine the peak-to-peak ripple and de output voltages in Figure below. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Rure 120 V ms 100 R 3.3 kf) 100 uF allle

(a) What value of filter capacitor is required to produce a 1% ripple factor for a full-wave rectifier having a load resistance of 1.5 KN. Assume the rectifier produces a peak output of 18 V. (b) Determine the peak-to-peak ripple and de output voltages in Figure below. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Rure 120 V ms 100 R 3.3 kf) 100 uF allle

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
a half-wave rectifier circuit in the figure below has a transformer inserted between the source and the remainder of the circuit. The source is 240 Vrms at 60 Hz, and the load resistor is 20 ohm. (a) Determine the required transformer turns ratio (Ns/Np) so that the average load current is 12 A. (b) Determine the average current in the primary winding of the transformer.
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, The transformer is specified to have a 12 V rms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
In a centre-tapped full wave rectifier, the diode having a forward resistance of 3 ohm and the load resistance equals to 750 ohm. The turns ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS) 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency.
A fully controlled three-phase rectifier bridge circuit supplies a dc load of 300V,60A, from 415V 3-phase ac supply via delta-star transformer. (i) Determine the required thyristor and transformer specifications. (ii) Draw the load and thyristor voltages when firing angle alpha = 60°. (ii) If a commutating diode is placed across the load, determine the FWD specification and then calculate the average load voltage and FWD average current when firing angle alpha = 45°
Draw the circuits, voltage and current plot of: a. A halfwave rectifier with capacitor filter b. A fullwave rectifier with capacitor filter c. A Full wave rectifier with center tap transformer and derive the equations of all of them
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to-peak ripple in the output voltage
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is 33 V