Design a flat rubber belt that needs to transmit 100kW for a system consists of two pulleys of diameter 1.0 m and 1.5 m. The two shafts of the two pulleys must rotate in opposite direction. Center distance between the two shafts must be 3.6 m and must have a belt speed of 20 m/s. Cast iron is used as flat belt pulley material. A consideration of slippage of 2% at each pulley and 5% friction loss at each shaft, and 20% overload. Belt thickness is must be 15 mm and the safe stress of the belt is 2.5MPa.

Design a flat rubber belt that needs to transmit 100kW for a system consists of two pulleys of diameter 1.0 m and 1.5 m. The two shafts of the two pulleys must rotate in opposite direction. Center distance between the two shafts must be 3.6 m and must have a belt speed of 20 m/s. Cast iron is used as flat belt pulley material. A consideration of slippage of 2% at each pulley and 5% friction loss at each shaft, and 20% overload. Belt thickness is must be 15 mm and the safe stress of the belt is 2.5MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the maximum shear stress in the shaft material?
A hydraulic cylinder cylinder that pushes a heavy tool during the outward stroke, placing a compressive load in the piston rod as shown below. If the material for the piston is SAE 4130 WQT 1300 Steel, and stress concentration factor is 1.0 for this design problem. If also it is given that the estimated actual endurance limit in this application sn ' = 22.3 ksi, and the fluctuating stress on the piston as: σm = 2.9 ksi, and σa = 4.1 ksi, please calculate the design factor based on the Goodman Criterion only: N = ___ . Please take the material property from the textbook, and you could just use your answer(s) from the problems above. Calculate your answer to 1 digit place.
A shaft ABC rotates at 500rpm and is driven through a coupling at the end A. At B a pulley takes off two-third of the power, the remainder being absorbed at C. The part AB is 1.5m long and of 100mm diameter, BC is 2m long and of 75mm diameter. The maximum shear stress set up in BC is 40MPa. Determine the maximum stress in AB and the power transmitted by it, and calculate the total angle of twist in the length AC. Take G = 80GPa.
You are asked to design a plain surface journal bearing to carry a steady radial load of 5.75 kN while the shaft rotates at 950 rpm. The shaft stress analysis determines that an acceptable nominal diameter of the journal is 62.5-mm and an l/d ratio is 1. The shaft is part of a machine requiring good precision. So a minimum radial clearance cmin= 0.040 mm seems appropriate. We shall use SAE 30 oil as a lubricant, at an inlet temperature of 45 oC. Analyze the hypothetical bearing,a) Determine the operating temperature Tave, and operating viscosity μave. b) Determine the minimum film thickness, ho, temperature rise of the lubricant, ΔTC, the total oil flow, Q, and side flow Qs in [mm3/s], the maximum film pressure Pmaxdeveloped in [MPa]. c) Determine the power loss, Hloss in [W], friction torque, Tf in [N-m] d) For minimum radial clearances, perform a design assessment using Trumpler’s criteria.
A security camera is to be mounted on a building in an alley and will be subject to wind loads producingan applied force of F0 cos(wf t) where F0 is measured to be 15 N. It is desired to design a mount such thatthe camera will experience a maximum deflection of 0.01 m when it vibrates under this load. The windfrequency is known to be 10 Hz and the camera mass is 3 kg. The mounting bracket is made of a solidpiece of aluminum, 0.02 x 0.02 m in cross section. Determine the length of the mounting bracket (l) that willkeep the vibration amplitude less than the desired 0.01 m. You may ignore torsional vibration and assumethe initial conditions are both zero. Note that the length must be at least 0.5 m in order to have a clear view.
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa. Calculate the polar second moment of area of the shaft?
A safety valve, 11 mm in diameter, is to blow off at a pressure of 1.5 MPa. It is held on itsseat by means of a helical compression spring, with initial compression of 16 mm. Themaximum lift of the valve is 27 mm. The ratio of mean coil diameter to wire diameter is5. The spring is made of cold drawn steel wire with ultimate tensile strength of 1400 MPa. (G = 81 370 N/mm2), Calculate:i. Wire diameter;ii. Mean coil diameteriii. Number of active coilsiv. Free lengthv. Pitchvi. Actual spring constantvii. Required Stiffness
A 25 mm diameter shaft is to be fit into a 25 mm ID bushing. What will be the clearance if the shaft is cooled by 25 °C while the bushing is heated by 30 °C? both the shaft and the bushing has a coefficient of thermal expansion of 11.6 x10^-6 m/m-°C.
The power transmitted between two shafts 3.5 metres apart by a cross belt drive round the two pulleys600 mm and 300 mm in diameters, is 6 kW. The speed of the larger pulley (driver) is 220 r.p.m. Thepermissible load on the belt is 25 N/mm width of the belt which is 5 mm thick. The coefficient offriction between the smaller pulley surface and the belt is 0.35. Determine : 1. necessary length of thebelt ; 2. width of the belt, and 3. necessary initial tension in the belt.[Ans. 8.472 m ; 53 mm ; 888 N]
A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². Thebelt is 200 mm wide and 12 mm thick.(a) Determine the maximum power that can be transmitted if the ratio of tight-side toslack-side tension is 2. The diameter of the driving pulley is 900 mm and the required speed of the output shaft is955 rev/min(b) Taking the belt thickness into account, determine the required diameter of theoutput pulley. (c) What would the required diameter be, assuming a total slip of 4%? (d) If the mass of the belt was neglected, explain the effect (with reasons) this wouldhave on the maximum power calculated in (a)
(a) Briefly discuss the functions of flexible mechanical elements. (b) A flat belt is 150 mm wide, 7mm thick, and transmits 11 kW of power at a belt rotational speed of 1750 revolutions per minute. The driving pulley is 150mm in diameter and the driven pulley is 450 mm in diameter. The pulley axes are parallel in a horizontal plane and 2400 mm apart. The open belt has a mass of 1017 kgm−3 of the belt volume, and the coefficient of friction is 0.3. Determine: (i) the tension in the tight and slack sides of the belt; (ii) the length of the belt.