3. Design a helical spring for a spring loaded safety valve for the following conditions :Operating pressureMaximum pressure when thc valve blows off freely= 1 N/mm?= 1,075 N/mm?Maximum lift of the valve wvhen the pressure is 1.075 N/mm26 mm%3DDiameter of valve seat= 100 mmMaximum shear stress400 MPaModulus of rigidity= 86 kN/mm²Spring index[Ans. d= 17.2 mm; D=94.6 mm ; n = 12]5.5%3D

Answered: Image /qna-images/answer/3e0a7b27-3f89-4688-84a9-db5841dcd22a.jpg

Design a helical spring for a spring loaded safety valve for the following conditions: Operating pressure Maximum pressure when the valve blows off freely = 1 N/mm? = 1.075 N/mm? Maximum lift of the valve when the pressure is 1.075 N/mm2 = 6 mm Diameter of valve seat = 100 mm %3D Maximum shear stress = 400 MPa Modulus of rigidity = 86 kN/mm?

Design a helical spring for a spring loaded safety valve for the following conditions: Operating pressure Maximum pressure when the valve blows off freely = 1 N/mm? = 1.075 N/mm? Maximum lift of the valve when the pressure is 1.075 N/mm2 = 6 mm Diameter of valve seat = 100 mm %3D Maximum shear stress = 400 MPa Modulus of rigidity = 86 kN/mm?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM: 5 A helical valve spring is to be designed for an operating load range of 90N to 195N. The maximum deflection of the spring for this load range is 7.5 mm. Assuming a spring index of 9, a permissible shear stress of 550 N/mm2 for the material and the modulus of rigidity of 0.85x105 N/mm2. Determine the dimensions of the spring. (i.e. Diameter of the spring wire ,Mean coil diameter, Outer diameter of the spring, number of active turn and free length of the spring). Assume the spring coil is squared and ground.
A helical spring is made of 10 m diameter steel wire wound on a 100 mm diameter mandrel. If there are 10 active coils what is spring constant Take: C= 100 GPA What force must be applied to the spring to elongate it by 50 mm?
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
Derive the stiffness matrix for a spring.
Subject : - Mechanical Engineering A helical spring is provided with a rigid plate at each end.A bolt passes through the spring and the endplates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and each plate is 25mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire ( E = 200 GPa and G = 80 GPa )
Problem 3: A helical spring is designed to have a stiffness of 500 N/m. The spring has a wire diameter of 5 mm and an outer diameter of 30 mm. Determine the number of coils required for the spring if the spring index is 6. Problem 4: A helical spring is compressed by a force of 100 N, resulting in a compression length of 20 cm. The spring has a wire diameter of 3 mm and a mean coil diameter of 15 cm. Determine the spring constant (stiffness) of the spring.
A mass weighing 11.5 kg falls a distance of 1.5 m upon the top of a helical compression spring. Determine the force applied on the spring if it compressed 203mm. Please show your full solution with unit analysis. Subject: Machine Design
A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turns
Plz give right answer. Calculate critical frequency of a helical spring of wire diameter 10 mm, mean coil diameter 50 mm and number of active coils 12. Take t = 550 MPa, G = 80 kN/mm².
Design and draw a valve spring of a petrol engine for the following operating conditions :Spring load when the valve is open = 400 N Spring load when the valve is closed = 250 N Maximum inside diameter of spring = 25 mm Length of the spring when the valve is open = 40 mm Length of the spring when the valve is closed = 50 mm Maximum permissible shear stress = 400 MPa
A washing machine with a mass of 60 kg and a drum radius of 15 cm, rotates at 1000 rpm and washes 3 kg of unbalanced laundry. a) How much dynamic force would be transmitted to the ground if no vibration isolation was taken from the machine?b) What would be the stiffness (k) of the visco-elastic floor if an insulation measure with a damping ratio of 0.1 was taken, which would reduce the force transmitted to the floor by 90%?
A helical spring is provided with a rigid plate at each end. A bolt passes through the spring and the end plates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and the plates are each 25 mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire (take E = 200 GPa and G = 80 GPa).