Design a multi-stage amplifier using the specifications below. After the necessary calculations are performed, simulate the circuit in Multisim and make any corrections/changes to the circuit, as necessary. Part I: Amplifier Specifications. • Use no more than three 2N3904 transistors. • The overall amplifier gain should be at least Av = +50 • Input signal should be at • Your circuit load • The input resistance, • The output resistance, . • VCC ≤ 20 volts • The output voltage, Vout is not inverted from the input voltage, Vin.

Design a multi-stage amplifier using the specifications below. After the necessary calculations are performed, simulate the circuit in Multisim and make any corrections/changes to the circuit, as necessary. Part I: Amplifier Specifications. • Use no more than three 2N3904 transistors. • The overall amplifier gain should be at least Av = +50 • Input signal should be at • Your circuit load • The input resistance, • The output resistance, . • VCC ≤ 20 volts • The output voltage, Vout is not inverted from the input voltage, Vin.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Design a multi-stage amplifier using the specifications below. After the necessary calculations are performed, simulate the circuit in Multisim and make any corrections/changes to the circuit, as necessary.

Part I: Amplifier Specifications.

• Use no more than three 2N3904 transistors.

• The overall amplifier gain should be at least A_v= +50

• Input signal should be at

• Your circuit load

• The input resistance,

• The output resistance, .

• V_CC ≤ 20 volts

• The output voltage, V_out is not inverted from the input voltage, V_in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Design a linear amplifier, based on a bipolar junction transistor 2N3904 in common emitter configuration. The supply voltage is 28V. The quiescent operating collector current for the amplifier should be around 10mA. The data sheet for the transistor shows that the DC current gain at this operating current is about 200. Draw the circuit diagram of your design. Label all the components in the circuit. Show all the voltages and currents that you use for calculations in your design. Label them using consistent naming convention.
The circuit in Figure below is a BJT common collector amplifier. Obtain expressions for both the voltage gain (AV = Vout / Vin) and the current gain (AI = Iout / I in). Assume Vin >> VBE please need steps explanation so I can understand and learn. thanks in advance Please in typing format please
For amplifier design, consider a very large load resistance RL . Use a 15 V DC source and a sinusoidal input signal of 200 mVpp and 1 kHz. Hint: you can start by choosing a collector (Icq) or drain (IDQ) operating current between 5 mA and 10 mA. 1. Design an input stage with a common drain amplifier that complies with thefollowing specifications: Voltage gain greater than or equal to 1 (Av1 ≥ 1). Input impedance greater than or equal to 250 kΩ (Zi1 ≥ 250 kΩ). Output impedance less than or equal to 2 kΩ (Zo1 ≤ 2 kΩ). Low cut frequency less than or equal to 20 Hz (fcb1 ≤ 20 kHz). Use a 2N3819 (NTE312) transistor.
An operational amplifier has a very high gain. Do you think having a very high gain is good or not? Explain your answer.
Convert the inverting amplifier shown to thetransresistance amplifier as shown(66) using a Nortontransformation of vi and R1. What are the expressionsfor iTH and RTH? Write a expression forthe gain vo/vi.
Draw the dc equivalent circuit and find the Qpoint for the amplifier shown . Assume Kn = 500μA/V2, VT N = −2V, VDD = 18V, RI = 2kΩ,R1 = 6.2 kΩ, RD = 7.5 kΩ, and R3 = 51 kΩ.
1. For n-stage analog amplifier circuit, if the voltage gain of each stage is Adi and the op amp common-mode rejection ratio is CMRRi (I =1~N): a) derive the mathematical expressions for the CMRR for the whole circuit b) analyze which stage’s CMRR has the most influence on the overall CMRR.
Design an inverting amplifier with an input resistanceof 15 kohm and a gain of 28 dB. Choose valuesfrom the 1-percent resistor table .
(a) A non-inverting amplifier is implemented with two 10 kΩ resistors with 5% toleranceWhat is the range of possible values for gain A? (b) Repeat for an inverting amplifier.Present theoretical calculations and confirm results in simulator (multisim, proteus).
Design a noninverting amplifier with an input resistanceof 100 k ohm and a gain of 6 dB. Choose valuesfrom the 1-percent resistor table,and use values that are no smaller than 2 k .
Find the relationship between the output and the input in the amplifier circuit depicted in Figure Q3.a & Q3.2. State any assumptions you make. [Derive the formula of gain]
Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes, sketch a circuit.''please solve it in computer font, not on paper''