Design base resistor bias circuit for a CE amplifier such that operating point is VCE = 8V and Ic= 2 mA. You are supplied with a fixed 15V d.c. supply and a silicon transistor with 6 100. Take base-emitter voltage VBE=0.6V. Calculate also the value of load resistance that would be employed. %3D

Design base resistor bias circuit for a CE amplifier such that operating point is VCE = 8V and Ic= 2 mA. You are supplied with a fixed 15V d.c. supply and a silicon transistor with 6 100. Take base-emitter voltage VBE=0.6V. Calculate also the value of load resistance that would be employed. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Draw the small signal models for the two transistor sources as shown andconvince yourself that Rout…

A: Given circuit is =

Q: If VA=∞, calculate the voltage gain of the common-emitter amplifier shown below in Figure in terms…

Q: 11.13 The i-v characteristic of an n-channel enhancement MOSFET is shown in Figure P11.13(a); a…

A: First, write the KVL in the output and write the equation,

Q: 1.2 Develop the small signal model for a two-terminal device formed by a MOSFET with its gate tied…

Q: Choose the correct answer: a) The reason of high input resistance of the MOSFET is: 1. The insulator…

A: MOSFET (Metal oxide Semiconductor Field Effect Transistor ) is Field effect transistor having 4…

Q: The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit,…

Q: Calculate the gate to source voltage, VGS, for a NMOS transistor having a parameter B…

A: a) We need to calculate the gate to source voltage VGS for a NMOS transistor having a parameter…

Q: +5V +5V 2MQ 2MQ Equivalent to B2=100 B,=100 By combining two NPN transistors, you will be able to…

A: Transistors are current-controlled electronics switch which can work in Active, Saturation and Cut…

Q: ICA analysis For the ICA circuit shown below perform the analysis and derive the expression of…

Q: Consider the circuit on the right. Use the simplified transistor model. The capacitors may be…

A: According to the question, we need to explain the characteristics of the amplifier shown below

Q: 1. Calculate the component values necessary to give the design of a Class B common emitter amplifier…

Q: 4a) For the circuit shown to the right, draw the small signal equivalent circuit (including ro). Be…

A: Note: As per company guidelines, only the first question will be solved as both the questions are…

Q: Vcc= 3.6 V, VBB = 2.8 V, Rc = 7 kN, RB = 560 kN, RE= 3 kN, R = 7 kN npn transistor parameters are…

Q: Design the bias circuit shown below for CS amplifier. Assume the MOSFET is specified to have Vt-1 V,…

A: The direction in which DC from a battery or power supply flows between the emitter and the base of a…

Q: VDD=6V Rp = 30KO Vo k'= 100HA/V? C3 M2 W/L 50 VIN = 0.7V %3D 2=0 (For DC Analysis) 2=0.01V (For…

Q: VCC 10V R3 1k0 R1 ΣΤΟΚΩ Construct the following circuit, A BJT transistor with R2 BETA of 100, R1…

Q: Gain of the amplifier falls of at high frequency due to internal capacitance of MOSFET. Determine…

A: Given the MOSFET operating in the linear region with drain to source voltage of 1 V. Given, the gate…

Q: VT = 0.026 V and VBE = 0.7 V. The two transistors are identical. %3D a) What does "the two…

A: Given : Note : It is the kind notice that student wants answer for only question a, hence we have…

Q: (h) A MOSFET in saturation is characterised by the following expression for the drain-source current…

A: In this question we have to find out transconductance in terms of gate to source voltage and MOSFET…

Q: Consider the following common emitter amplifier: Discuss the LIMITATIONS of this circuit in terms…

A: We need to discuss the limitation of this circuit in terms of linearity and in terms of impedance…

Q: E MOSFET SGD Rs 5k Vo 10 kQ Rd 2 RL 2 kQ Vi sine +\ Vd 10 V Vs 10 V zi

Q: If the drain current Ip of a MOSFET transistor (operating in saturation region) is divided by two…

A: Solution: Note: It is kindly notice that here both the questions are different so according to the…

Q: 1- What is the lowest value of de collector current to which a transistor having the characteristic…

Q: IBQ, ICQ, VE, VCEQ, VCfor a transistor with VBE= 0.6 and β = 50. Draw and label the DC load-line.…

A: We need to find out current and voltage for given circuit

Q: the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD = 5.6…

Q: Assuming VTh = 0.4 V for NMOS transistors and VTh= - 0.4 V for PMOS transistors, the MOSFET…

A: To find out the correct answer

Q: Design a Common Emitter Voltage Divider Bias Amplifier circuit using. The current gain of the…

A: Given values, Supply voltage, VCC= 18 V Collector current, ICQ= 10 Ma Current gain, β= 75 collector…

Q: In the BJT circuit below, assume VBE 0.6V and CE current gain ß very large. Then the collector…

A: Given circuit, Base emitter junction voltage, VBE=0.6 V CE current gain β very large

Q: For a particular IC-fabrication process, the transconductance parameter k'n = 400 μA/V2, and Vt =…

Q: A MOS transistor is biased at a drain current of Ip, with K= C=100 HA/Vv and V7 = 1 V as shown in…

Q: 1. Design a MOSFET circuit with zero bias using a 2N3797 that operates from a +9 V de supply and…

Q: Consider the source follower circuit in Figure shown below, IQ = 10 mA VTP = -2 V, Kp = 5mA/V2, RL =…

A: *Keeping a note ?as per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts.…

Q: A MOS transistor is biased at a drain current of I, with K = HC 100 µA/V and V, =1 V as shown in the…

Q: State whether the following statements are TRUE or FALSE 1 A class A amplifier should be biased…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: When the gate-to-source voltage (VGs) of a MOSFET with threshold voltage of 400 mV, working in…

Q: In an n-p–n transistor in the common emitter configuration, an ac input signal of ± 50 mV is…

A: Given, AC input, Vin=±50 mV βdc=90, βac=120 VB= 0.7V, IB=17mA, Ib=±7 mA

Q: For the circuit shown in the Figure, the transistor has the parameters as below. Let RB=30k2.…

Q: (a) Find the value of R, to establish a de emitter current of about 0.2 mA. (b) Find R. to establish…

Q: In the circuit below, the transistor has Ic = 1mA, IB = 5µA, and VBE = 0.5V. The source %3D current…

Q: Design a MOSFET circuit with zero bias using a 2N3797 that operates from a +9 V dc supply and…

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: Sketch the FET transfer curve defined by pinch of voltage of (- 5 V) and source current of (10 mA)…

A: FET is a voltage-controlled three-terminal device. The current-voltage relation in the saturation…

Q: In the figure, A characteristics curve is shown for the MOSFET. Determine the following outcome and…

A: We need to find out drain current and transconductance for given characteristic

Q: For an NMOS common gate amplifier, the bias current is 10 uA, aspect ratio is 10, K, = 100 uA/V? and…

A: Since there are two questions, as per company policy we will solve only 1st question. If other…

Q: In the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD =…

A: RL=0.k ohm

Q: A common emitter transistor amplifier working in active mode of operation has collector current of 1…

A: Given: A common emitter transistor amplifier working in active mode has, Collector current, IC=1 mA…

Q: Design a common emitter amplifier for a Vout of+-6.3V. Vcc is set to 9V. At x=1, Av=12.6 V/V and the…

A: We need to design a common emitter amplifier for a Vout of ±6.3V and Av=12.6 V/V. Also, Rout must…

Question

I need the answer as soon as possible

Design base resistor bias circuit for a CE amplifier such that operating point is VCE = 8V
and Ic= 2 mA. You are supplied with a fixed 15V d.c. supply and a silicon transistor with B
= 100. Take base-emitter voltage VBE = 0.6V. Calculate also the value of load resistance that
would be employed.
ВЕ
Vec-15V
Ri 20KN
Rc-2KN
R:8OKA
RE 1KN
HI

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

What is the voltage gain of the common-emitter amplifier as shown? Assume βF = 135, VCC = VEE = 10 V, R1 = 20 kΩ, R2 = 62 kΩ,RC = 13 kΩ, and RE = 3.9 kΩ.
If the circuit of problem 2 is configured as a common-emitter amplifier, calculate the resulting voltage and current gain. Assume a load resistor of 1k ohm. Circuit of problem 2: determine the operating point of a universal trasnsistor DC bias cirucit when Vcc=15V, R1=10k ohm, R2=2.2k ohm, Rc=680 ohm, Re=100 ohm. Assume beta (b)=200 and Vbe=0.72V.
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
4) By drawing the small signal model of the circuit given below, we can determine the total voltage and current gain values of the circuit, without the bypass capacitor on and without the bypass capacitor. Calculate separately for the two cases as it will be in the circuit (connected to the emitter end of the transistor). (β = 100, rS = 600 Ω, R1 = 27 KΩ, R2 = 4.7 KΩ, RC = 3.3 KΩ, RE = 680 Ω, RL= 15 KΩ, VCC = 10 V)
SOLVE NUMBER 2 .1. Solve the output voltage if the gain is 24 db with aninput of 5mV.? 2. Assume a load resistor, RL of 2.2kΩs and a supply voltage of 24v. Calculate the Collector current (Ic) flowing through the load resistor when the transistor is switched fully "ON", assume Vce = 0, & β = 100. Also find the value of the Emitter resistor, Re with a voltage drop of 1.3v across it, R1, R2, and Ib. Assume also a value of 9 times Ib flowing through the resistor R2, while 10 times Ib flowing through R1.
a) Differentiate between Common Emitter (CE), Common Collector (CC) and Common Base (CB) amplifiers. b) Do the DC Analysis of the circuit below and find out the DC collector voltage?c) Do the AC Analysis of the circuit below and find out the AC collector voltage?R1=30kΩΩ=610Ω
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
A. Design a fixed bias-transistor circuit using VBB = VCC = 10 V for a Q-point of IC = 5 mA and VCE_ 4 V. Assume βDC = 100.The design involves finding RB and RC. B. 4. Design an emitter bias network at Q-point ICQ = ½ ICsat and VCEQ = ½ VCC. Use VCC = 20 V, ICsat = 10 mA, β = 120, and RC = 4RE
For the MOSFET amplifier, given VDD = VSS= 8V, Rsig = 2Kohm, R3=3Kohm, Kn =K’n(W/L)= 0.5 mA/V2, Vtn= 1.2V, λ ≅ 0, Q point (0.8mA, 2.5V).Determine RD in Kohm
the transistor in the circuit above has gm=0.11mS and ro=33Kohm. Given the following condition: R1=770Kohm, R2=890Kohm, RD=5.4Kohm, R3=20Kohm, R6=6.9Kohm, Rsig=2Kohm, determine the input impedance of the amplifier in Kohm.
Consider a voltage-divider configuration of n-channel enhancement-type MOSFET where R1 = 12 MΩ, R2 = 7 MΩ, RD = 3 kΩ, RS = 1 kΩ. The MOSFET has a threshold voltage VGS(Th) = 3V, and one example point on the transfer characteristics curve is VGS(on) = 6V, ID(on) = 5 mA. Determine VGSQ, IDQ, Vs, VD, VDS assuming VDD = ( 80 ÷ 10 ) +20 V