Design the chilled water pipes system shown in the figure below and find the power of the pump assuming that the pressure loss in each elbow is equivalent to the pressure loss produced by 5m of the pipe length. A 20 Lit/min D 10m 16m- A C pump Chiller 8m B 30 Lit/min 11 24 E 8m 6m 8m F 40 Lit/min

Design the chilled water pipes system shown in the figure below and find the power of the pump assuming that the pressure loss in each elbow is equivalent to the pressure loss produced by 5m of the pipe length. A 20 Lit/min D 10m 16m- A C pump Chiller 8m B 30 Lit/min 11 24 E 8m 6m 8m F 40 Lit/min

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the minimum diameter of a smooth tube to ensure the flow of water at an average velocity of 100 cm/s remains turbulent. Use vwater = 1E-6 m2 /s. [Ans.: 4 mm]
As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of 5,664 liters/s, passing through a pipe with a diameter of 50.8 mm and a length of 121.92 m. Some of the local losses in the system are also shown on the figure. Calculate the effective power of the pump by taking the relative roughness ɛ / d = 0.001 Note: For all questions, pwater = 1000 kg/m³, g=9.81m/s^2 , the kinematic viscosity of water is 1.0219x106 m²/s and the questions can be solved by accepting the values that are not given.
Design the duct system shown below using Equal friction method, and determine the fan power when the fan efficiency is 68%. The duct is circular. Take the velocity in the main duct AB equal to 7 m/s. Assume a dynamic loss coefficient of 0.5 in T fitting and 0.8 in elbow fitting. Given AB = BC = 10m and BD = 25m .
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total length of the 10-in-ID pipes is 62 ft. and the friction factor is taken as 0.022. If the pump head H can be defined as a function of discharge Q in ft3/s is: H = 365 - (0.04718Q^2), in feet. What is the operating discharge rate in ft3/s?
The old Hydraulics laboratory in Mechanical Engineering used a roof tank tosupply apparatus with water at a nearly constant head. The water wascollected in an under floor sump, and then pumped back to the roof tankafter the experiment. The flow rate was 10 litre s-1. The tank was 6m abovethe sump, and the length of the pipe route was 15 m. The old 6” pipes arenow heavily corroded (k = 7.5 mm). The old pump has been scrapped. Whathead ΔH would be specified for a pump to restore the system using the oldpipes? What would the pump power be? If the pipes were replaced with 150mm diameter PVC pipes, what pump ΔH would be required?
The water is flowing througha pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 0.035 m /s. The section1 is 7500 mm above datunm and section 2i5 500 cm above datum. If the pressure at section 1 is 420 kPa, find the intensity of pressure at section 2.
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
The diameter of the smooth pipes used in the pumping system in the lower figure is 150 mm and its total length is 80 m. In this system, there are four elbows with a loss coefficient of 0.2. It's lost its coefficients are 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the inlet to the tank. z2-z1=15 m, above manometric pressure if the flow of water pumped into the tank is 50 L/s and the overall efficiency of the pump is %84 find his height and strength. Take the viscosity of water is 0.001 kg / m.s
A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
Rate the flow inside a pipe with Re = 1.8x10^4 and ε/D = 0.027. A: Turbulent totally rough B. Hydraulically smooth turbulence C. Laminar, with f=64/Re D.Transient roughness turbulence