Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 mm of length. G = 80GN/m2
Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…
A:
Q: A 6-splined shaft delivers a torque of 7.5 kN - m. The spline has the following dimensions: D = 75…
A: given; →torque(T)=7.5KN-m =7.5*106N-mm→outer diameter(D)=75mm→inner…
Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060…
A: Given Data: Allowable shear stress, t=5800 psi
Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…
A:
Q: In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a…
A:
Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…
A: Given: Power transmitted by the shaft P=75kWSpeed of the shaft N=200rpmModulus of rigidity…
Q: Q1. Explain use of Shaft and its types. Q2.Explain Design Procedure of Shaft Subjected to twisting…
A: 1.Uses of shaft A shaft is a rotating machine component, typically circular in cross section that is…
Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…
A: for solution refer below images.
Q: The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a.…
A: Given data: Diameter of the solid shaft, D= 10mm Shear stress, s=75MPa=75N/mm2
Q: A solid circular shaft is required to transmit 200 kW while turning at 90 rpm (rev/min). The…
A: Consider a shaft having diameter 'D' is subjected to a twisting moment 'T'. Then, from torsion…
Q: 4) Shafts with lengths 5m and 4 m are connected by gears. The diameter and shear modulus for both…
A: Given, Lengths of the shafts , 5 m and 4 m. Diameter of the shafts , d = 10cm Shear modulus of the…
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…
Q: A solid circular steel shaft having an outside diameter of 1.75 in. is subjected to a pure torque of…
A: Given data: ◆ The diameter of solid circular shaft: D = 1.75 inch ◆ The torque applied on the shaft:…
Q: Determine the internal torques, T₁ and T2, in segments (1) and (2), respectively. Use the internal…
A:
Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…
A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).
Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…
A:
Q: 2.0 in. solid shaft transmits power at 120 rpm. If the allowable shearing stress is 12ksi. (a)…
A:
Q: the twisting angle. The modulus of Rigidity for the shaft is 20 GN/m? • for the missing torque T =…
A: For the shafts in series,…
Q: 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total…
A: Given:Diameter of gear, d=220 mmpressure angle, ϕ=14.5oPower, P=50 kWSpeed, N=580 rpm
Q: 75 N.m C 125 N.m 2 m 1m A steel shaft is fixed at A and is subjected to the torques as shown.…
A: Given data: dAB=50 mmdBC=30 mmG=77 GPa Need to determine the torque in segment AB, BC and angle of…
Q: The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a…
A:
Q: (a) A steel transmission shaft is 510 mm long and 50 mm external diameter. For part of its length it…
A: We can consider this case as shafts in series Both parts are subjected to the same torque We know…
Q: A steel shaft ABCD having a total length of 3.5 m consists of three lengths having different…
A: Torque is the rotational equivalent of linear force. It is also referred to as the moment, moment of…
Q: A tubular steel [G = 79 GPa] shaft with an outside diameter of D = 89 mm and a wall thickness of t =…
A: Given Data The modulus of rigidity is: G=80 GPa The outside diameter is: D=89 mm The thickness of…
Q: A solid constant-diameter circular shaft is subjected to the torques of TA= 480 lb-ft, TB = 1030…
A:
Q: n the case of circular shaft subjected to pure torsion nonzero are: (a)Nx (b)Nx and Vy (C)Mz and Vy…
A: In the case of circular shaft subjected to pure torsion nonzero are:
Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 10 N/mm² and length of…
A: Given data as per question shaft dimeter =125 mmPower transmitted =120 kwSpeed=160 rpmC = 8×10…
Q: Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree…
A: Given Data P=30 MW N=1500 rpm Angle of twist=1° L=20D G=80 GN/m2
Q: Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an…
A: Given data, Power=150hp speed=250 rpm shear stress=4.7ksi angle of twist =0.35°…
Q: A solid shaft 2 m. long is stressed 60 MPa when transmitted a power of 50 kW at 2 rev /…
A: Given: The length of solid shaft, L = 2 m The shear stress in shaft, τ = 60 MPa The transmitted…
Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…
A: Given:Length of the hollow shaft, L=1 mPower transmit, P=30 kWSpeed of the shaft, N=700 rpm,Angle of…
Q: Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it…
A:
Q: The outside diameter of a hollow shaft that is twice its inside diameter the ratio of its torque…
A: This question is related to the solid shaft and hollow shaft. For the solid shaft, Shear stress…
Q: A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the…
A: The problem is based on strength of material
Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…
A:
Q: The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the…
A: Given: The allowable shear stress, τ = 75 MPa The speed of the shaft, N = 300 rpm The power of the…
Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…
A:
Q: 4. The tapered shaft is made from E- 36 steel ( G = 80 GPa ), and has a radius which can be…
A: Given Torque, T = 450 Nm Length, L = 4 m Find Angle of the twist
Q: shaft
A:
Q: The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and…
A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…
Q: 2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the…
A:
Q: The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer…
A:
Q: 3 T 100 mm 75 mm В 3.00 m 2.70 m G=28 GPa G=35 GPa
A: Stress: When a component or a part is subjected to any external force, a resisting force will be…
Q: Problem 1
A: Due to the torques at point B, C, D, E, and G, there exists a reaction torque at point A.Sign…
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A:
Q: A solid circular steel shaft having an outside diameter of D = 1.00 in. is subjected to a pure…
A:
Q: if you wrong i will dislike. A motor driving a solid circular steel shaft transmits 40 kW of power…
A: Given Data ⇒ Power transmitted by motor (P)=40 KWSpeed (N)=500 rpm Diameter of the shaft (d)=40…
Q: The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the…
A:
Q: A hollow nickel-steel shaft, whose outside diameter is twice the inside diameter, is to transmit…
A:
Determine the diameter of a solid
steel shaft that will transfer 30 MW
at 1500 RPM with a 1 degree twist
angle for every 20 mm of
length. G = 80GN/m2
Step by step
Solved in 2 steps with 2 images
- Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 mDetermine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it rotates with revolution of 67.6 RPS. Maximum torsional stress equivalent to 50000 kPa.
- Determine the torque that can be transmitted by a shaft of 50 mm diameter, if the maximum allowable angle of twist is 2° in a length of 100 cm. Take G = 80000 .The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the figure. Determine the maximum permissible value of T subject to the following design conditions: F.S. = 1.5, Tult steel = 95 MPa, Tult aluminium = 70 MPa, and o < 6° (9 is the angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminiumCalculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
- A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questionsDetermine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2000 N-m and a torque of 4300 N-m if the diameter of the hole is equal to 0.7 of the outer diameter of the shaft. The shaft rotates and loads are applied suddenly, with minor shocks. The maximum bending stress is equivalent to 88 N/mm2. Apply ASME Code for this problem.
- A 3-m steel shaft is to transmit 100 kW at 300 rpm. It carries two gears each weighing 1.9 kN supported at a distance of 1 meter from each ends. Assuming an allowable shaft bending stress of 117 MPa, determine the diameter of the shaft in mm using ASME code (assume Km = 1.0 and Kt = 1.0)A shaft is made of a steel alloy having an allowable shear stress of 10 ksi and the diameter of the shaft is 1.2 inch determine the maximum torque T that can be transmitted.A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50 kW and 25 kW, respectively. Compute the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.