4) Shafts with lengths 5m and 4 m are connected by gears. The diameter and shear modulus for both shafts are 10 cm and 160 GPa If the torque at gear D is 5 kN.m, calculate the following; a)Internal torques of the shafts b)Angles of twist for shafts c) Rotation angles of gears B, C and D 5m 4m (1) 72 teeth (2) 108 teeth

4) Shafts with lengths 5m and 4 m are connected by gears. The diameter and shear modulus for both shafts are 10 cm and 160 GPa If the torque at gear D is 5 kN.m, calculate the following; a)Internal torques of the shafts b)Angles of twist for shafts c) Rotation angles of gears B, C and D 5m 4m (1) 72 teeth (2) 108 teeth

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The transmitted torque of a hollow shaft is 3400 N-m at a shearing stress of 55 MPa. If the outside diameter is 1.25 times that of the inside diameter, what is the inside diameter, in mm?
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shownin Fig. 14.19 has ratio of belt tensions 4.The gear forces are as follows :Ft = 1590 N; Fr = 580 NFig. 14.19Design the shaft diameter by maximum shear stress theory. The shaft material has the followingproperties :Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.[Ans. 20 mm
ach student has been allocated a different shaft length, L and a different allowable maximum shear stress,τmax and subject to a different Torque, T. For steel use a shear modulus, G=80,000 MPa.A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate:a) The minimum shaft diameter required.b) The angle of twist over the length of the shaft.c) The Power output if your shaft is rotating at 2000 rpm. L=1.9m τmax=95MPa T=1.5kN-m
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
An aluminum bar of circular cross-section and the profile specified in Prob. C2.1 is subjected to a 15-N · m torque. Use numerical integration to compute the angle of twist of the bar. For aluminum, use G = 30 GPa. Please explain how to do it. Thank you
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
2. A rectangular key was used in a pulley connected to a line shaft at 23 HP and 10 rps. If shearing of key is 230 Mpa, determine the force acting on key length if key width is one-fourth of shaft diameter and key length of one inch.
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
Shaft length, L and a different allowable maximum shear stress, τmax and subject to a different Torque, T. For steel use a shear modulus, G=81,000 MPa. A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate: a) The minimum shaft diameter required. b) The angle of twist over the length of the shaft. c) The Power output if your shaft is rotating at 2000 rpm. L= 1.6m, τmax=100MPa , T=1.3kN-m
What is the diameter of a solid shaft that will not twist through more than 1.5° in a 200 cm length when subjected to a torque of 120 Nm? Take G = 83000 MPa.