A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The gears at B and C drive machinery that requires 25 kW and 10 kW of electricity, respectively. Calculate the angle of twist between the motor A and the gear at position C (Use G = 80 GPa) Motor B 50 mm

A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The gears at B and C drive machinery that requires 25 kW and 10 kW of electricity, respectively. Calculate the angle of twist between the motor A and the gear at position C (Use G = 80 GPa) Motor B 50 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.16P: Solve the preceding problem if the shaft has an outer diameter d2=150 mm and inner diameter d1= 100...

See similar textbooks

Related questions

Q: For pocket operation of 2 x 3 inch surface and dept of 0.06 in using 0.5 in end mill tool. What is…

Q: Cin the surrounding

Q: 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)ay' (c)Tx'y

A: Solution is attached below

Q: DONT MIND THE BIG NUMBER ON THE RIGHT, IT IS JUST FOR NUMBERING. MAKE SURE IT IS CORRECT AND…

A: GIVEN DATA- A REFRIGERATOR MECHANISM GIVEN WE HAVE TO FIND TORQUE CREATED

Q: Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 80…

Q: Large cut. From a circular disk with uniformly distributed mass M and radius R, a smaller circle of…

A: To determine the center of mass.

Q: For the mechanism shown in the figure, determine the torque TA required at crank AB to maintain…

A: Given: r=8 inh=16d=20θ=-330°φ=30°

Q: single-stage centrifugal pump has an impeller speed of 1750 rpm. If the flow rate of water is 60…

Q: Galaw-galaw. A post weighing 314. [N] and with height h has its lower end 0.214. The upper end is…

A: Given Data The weigth of the post is:W=mg=314N The coefficient of static friction is:μs=0.214 The…

Q: a. Determine the resultant and direction in the system shown. b. Calculate the moment about point A…

Q: a) The company has two diesel-powered standby generators, both of which are capable of supplying…

A: Answer: 2-stroke engine 4-stroke engine 1. Brake Power (10π) kW (10π) kW 2. Indicated…

Q: A single-stage centrifugal pump has an impeller speed of 1750 rpm. If the flow rate of water is 60…

A: Given Speed, N = 1750 rpm Flow rate, Q = 60 gal/min = 0.0037 m3/sec Assume,…

Q: 3 kip.ft 3 ft A - 6 ft B

Q: Scalar ng Bayan. The vectors k and in the figure have a magnitude of 10.00 [m] and 5.00 [m],…

A: OPTION 4 Is correct answer

Q: Question 1: For the given state of stress, by using formula determine; 25 MPa - Principal Plane…

Q: A gas is flowing at a supersonic velocity in a gradually increasing cross- sectional area. Assuming…

A: To find :- Correct option

Q: Replace the loads acting on the beam, as shown by a single resultant force R and find its location…

Q: Consider a modification of the cold air-standard Otto cycle in which the isentropic compression and…

Q: Compute the discharge velocity of air in ft/s if a turbo-compressor is used to compress 18 pounds…

Q: What are the components of a Drone? For your response: Research and identify at least one component…

Q: Determine the shear force 7.59 ft to the right of point A for the beam shown belowif T = 1094 lb ft,…

Q: he figure shows the stresses at a point. Determine the principal stresses and the maximum shear…

A: Given data as per the question σx=4000 lbplg2σy=9000 lbplg2τxy=3000 lbplg2

Q: (Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter…

A: The torque capacity of the flange coupling is 5522.33 lb•ft.

Q: Sentences tic strength of the gear tooth is based on....... strength bending b. compressive c. shear…

A: Ans: 1. b. Compressive 2. a. Surface 3. b. Max 4. b .two 5. c. Helix angles 6. c. Less than…

Q: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the…

Q: 3. For the figure shown below, if the coefficient of friction at the wall is 0. determine the…

Q: 9. If the coefficient of static friction at contact points A and B is 0.3, determine the vertical…

Q: An orifice meter with a throat diameter of 5-mm is set in a 75-mm pipeline containing flowing water…

Q: An ideal Trinkler cycle using 2 kg of air as working fluid has the following properties at the…

Q: 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)ay' (c)tx'y'

Q: What type of heat exchanger is a waste heat boiler? Is it a regenerator or a recuperator? Choose…

A: Waste heat boiler is a boiler in which steam is heated by utilizing heat from the flue gases.…

Q: CS South-line. Consider a sphere with radius R and mass M. Assuming that the moment of inertia of…

Q: Assume that friction in the suction line is negligible. Toluene @ 35C is pumped from an open…

A: Temperature of the Toluene, T=35oCDischarge tank pressure, P2=150 kPa=150*103 PaPump position from…

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

Q: With the increase in pressure, a. enthalpy of dr y saturated steam first increases and then…

Q: A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a total capacity of 12…

Q: Calculate the net heat flux per unit area and by radiation between two infinitely large parallel…

A: Introduction: Radiation heat transmission occurs in the form of electromagnetic waves, primarily in…

Q: h y= ) Locate the centroid (x, y) of the shaded area shown. y -X

A: Given Datay=-ha4x4Find the centroid

Q: • A prismatic beam of trapezoidal section shown in figure is subjected to sagging B.M Calculate the…

A: When a beam having Young's Modulus of Elasticity E is subjected to Bending Moment M then, bending…

Q: 6. Saturated vapor at 5.4 Mpa h= S=

A: According to the details provided in the question, we need to calculate enthalpy and entropy

Q: ding moments diagrams that belong to the beam given below, where

Q: A particle moving in the x-y plane has a velocity at time t = 5.25 s given by (3.9i+ 6.0j) m/s, and…

Q: The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below.…

A: Answer: (a) The load P is 70875 N. (b) The minimum diameter for pin C is 22.62 mm. (c) The minimum…

Q: Determine the shear force 7.5 ft to the right of point A for the beam shown belowif T = 1080 lb ft,…

Q: Design 3 Dwell at zero displacement Rise linearly by 22 mm Dwell at 22 mm Fall linearly by 22 mm…

Q: A thin cylinder 80 mm internal diameter, 250 mm long with walls 2.5 mm thick is subjected to an…

Q: From the given beam shown below, find the maximum moment of the beam.

Q: A 20-cm-diameter, 60-cm-high vertical cylindrical container, shown in side Figure, is partially…

Q: Consider a modification of the cold air-standard Otto cycle in which the isentropic compression and…

A: ● All of the above options are not matching. The Right answer is 1.36 kJ ( This solution is RIGHT to…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

draw fbd

A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The gears at B and
C drive machinery that requires 25 kW and 10 kW of electricity, respectively. Calculate the angle of twist between
the motor A and the gear at position C (Use G = 80 GPa)
1.2
Motor
50 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.