Determine the efficiency of a token ring with a data rate of 250Mbps, a ring latency of 120 µsec and 5000 bit packets. Assume N hosts want to transmit and each host holds the token for a maximum of frame transmission time

Determine the efficiency of a token ring with a data rate of 250Mbps, a ring latency of 120 µsec and 5000 bit packets. Assume N hosts want to transmit and each host holds the token for a maximum of frame transmission time

Principles of Information Security (MindTap Course List)

6th Edition

ISBN:9781337102063

Author:Michael E. Whitman, Herbert J. Mattord

Publisher:Michael E. Whitman, Herbert J. Mattord

Chapter6: Security Technology: Access Controls, Firewalls, And Vpns

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Related questions

Q: A 100 Mbps half-duplex link between two stations is established. If the distance between the two…

A: With half-duplex mode, each transmitted character is immediately displayed on a monitor. If a…

Q: Suppose nodes A and B are on the same 10 Mbps broadcast channel, and the propagation delay between…

A: Here we have given the solution for the question asked. You can find the solution in step 2.

Q: a digital communication system with the following specifications: Pbe=0.05, (n,k) block coding with…

A: It is defined as a element of a standardized code or protocol. Each code word is assembled in…

Q: 1. There is a data that has a file size of 26MB with an ethernet overhead of 8 Mb. Find the Total…

A: Solution- 1) Given a data of size of 26Mb with an ethernet overhead of 8 Mb. So, the total amount…

Q: Calculate the delay x bandwidth product for the following links. Use one-way delay, measured from…

Q: Suppose nodes A and B are on the same 10 Mbps broadcast channel, and the propagation delay between…

A: Consider following data: Rate of broadcast channel= Propagations delay between two node's=bit time's…

Q: Suppose that R = 1 Gbps and Rc is 300 Mbps and Rs is 200 Mbps. Assuming that the servers are…

A: EXPLANATION: As per the information given in the question, it can be said that: R = 1GBPS = 1024…

Q: Suppose nodes A and B are on the same 10 Mbps broadcast channel, and the propagation delay between…

A: ANSWER:-

Q: 6. Between two hosts A and B which are connected by a link with the bandwidth 1 Mbps and with a…

A: Given Data : Bandwidth = 1 Mbps RTT = 2 ms Tp = 1 ms = 1 * 10-3 Protocol used: Go Back N…

Q: part 1:…

A: As multiple questions are posted, only first can be solved and kindly repost the questions that are…

Q: Suppose users share a 2 Mbps link. Also suppose each user transmits continuously at 1 Mbps when…

A: Given: users share a 2 Mbps link. Also suppose each user transmits continuously at 1Mbps when…

Q: Q 1. (a) Data are transmitted over a particular Ethernet network in blocks of 1500 bytes. How many…

A: Actually, 1 byte = 8 bits.

Q: Host A and Host B are connected by a single 2 Mbps (Megabits per second) link that has a propagation…

A: The answer is..

Q: Q 1. Given the following network topology calculate the eigrp metric and show the best path for PCO…

A: Answer is given below

Q: Consider a data link where the data transmission rate is 2000 bits/sec and propagation rate is…

A: Actually, given data transmission rate is 2000 bits/sec.. propagation rate 1000m/sec..

Q: Compare GBN, SR, and TCP (no delayed ACK). Assume that the timeout values for all three protocols…

A: Go Back N:A sends 9 segments in total. They are initially sent segments 1, 2, 3, 4, 5 and later…

Q: a. How many bits are there in each packet? b. At what time the first packet will be received at…

Q: Suppose two nodes, A and B, are attached to opposite ends of a 900 m cable, and that they each have…

A: the answer is given below:-

Q: Question 4: Consider the figure below, with three links, each with the specified transmission rate…

A: 1.The delay on Link1 for one packet =Length of the packet in bits/Transmission rate Length of…

Q: Consider a network which uses a frame size oT RRo send data on a 1.5 Mbps link with a one-way…

A: Given: Frame Size: 1KB Bandwidth: 1.5Mbps Utilization: 60% Solution:- Transmission delay = Frame…

Q: onsider the data pipelining process in the writing of a HDFS block. Suppose the data packet size is…

A: below we find how many packet needed? =========================================================…

Q: 3.1 A 1-km-long, 10-Mbps CSMA/CD LAN (not 802.3) has a propagation speed of 200 m/isec. Repeaters…

A: Effective data rate = data (excluding Ack) / total time Total time = transmitter seizes cable +…

Q: Efficiency Principle: Ethernet V1 access protocol was designed to run at 10 Mbps over 2.5 Km using…

A: In V1 access protocol we have, Bandwith (B) = 10Mbps Distance (D) =2.5 Km Packet size (S) = 1500…

Q: c. Ignoring processing and queuing delays, obtain an expression for the end---to--- en delay. d.…

A: Propagation delay is the period of time taken for a sign to arrive at its objective. It alludes to…

Q: d) Assume that, in a Stop-and-Wait ARQ system, the bandwidth of the line is 5 Mbps, and 1 bit takes…

A: i. Its bandwidth-delay product: (5x106)x(80x10-3) = 400000 bits ii. The system can send 400000 bits…

Q: Host A and Host B are connected by a network with 2 store-and-forward switches. Each link has a…

A: GIVEN: Bandwidth: 5 megabits/second Distance between Host A and Host B: 1,000 kilometers Network…

Q: Question: Suppose two nodes, A and B, are attached to opposite ends of a 1200 meter cable, and that…

A: Below is the answer to the above question of both parts. I hope this will be helpful for you..

Q: A network with bandwidth of 10 Mbps can pass only an average of 12,000 frames per minute with each…

A: Answer : OPTION " b " is correct

Q: Consider that two hosts A and B are connected via a direct link with transmission rate of 30 Mbps.…

A: Given, Bandwidth = 30 Mbps Packet length = 1 MB distance between A and B = 100 Km Propagation speed…

Q: Assume that, in a Stop-and-Wait system, the bandwidth of the line is 3 Mbps, and 1 bit takes 30…

A: The given bandwidth is 3 Mbps that is 3 Mbps requires 30 milliseconds to complete a round trip.

Q: Assume the length of each message is L=5, the access link has a speed of X=180 Mbps, and there are…

A: Given Data : Length of message , L = 5 Speed , X = 180 Mbps Message arrival rate = 6 messages /…

Q: Consider the scenario shown below, with four different servers connected to four different clients…

A: In a power grid, a limited volume of electricity is transmitted for conforming the system security.…

Q: Suppose there are 4 nodes sharing a broadcast channel using TDMA protocol. Suppose at time t=0:…

A: Answer:- Time Division Multiple_ Access allow access to channel by giving a fix time slot to each…

Q: Consider the following network with given line speeds and lengths: Assume the speed of light is…

A: NOTE: As per guideliness, we are allowed to answer only first three dependent questions per posts.…

Q: Consider two hosts, A and B, connected by a single link of bandwidth R bits per sec. Suppose that…

A: The answer is...

Q: The next 4 questions are based on the following description: In all following calculations, assume K…

Q: b) Assuming two 1 Mbps Ethernet LANS (LAN Y and LAN Z) are connected by a bridge. An application in…

A: i) The total size of the frame = (1480 bytes)x(32 packets/sec)

Q: Consider the figure below, with three links, each with the specified transmission rate and link…

A: Total delay = Sum of transmission delay and propagation delay for each link Transmission delay =…

Q: Compare GBN, SR, and TCP (no delayed ACK). Assume that the timeout values for all three protocols…

A: Sequence= 1,2,3,4,5 and Acks=2,4,5,6 (Ack 2 means packet 1 is reached safely). Ack 2 is missing send…

Q: an asynchronous 8 bit transmission using a UART (8051), the crystal in use is 22.1184 MHz. The…

A: It is defined as Universal Asynchronous Receiver Transmitter. It is a hardware peripheral that is…

Q: What is the delay of sending a data file from a source station to a destination station? Suppose…

A: Here the total delay for sending file from source to destination => Transmission delay +…

Q: 1) How long does it take a packet of length 1,000 bytes to propagate over a link of distance 5,000…

A: The given data is: The length of the packet is 1,000 bytes.Here, the length is given in bytes first…

Q: 1. A pure ALOHA network transmits 200-bit frames on a shared channel of 200 kbps.What is the…

A: Throughput of PURE ALOHA is S = G X e-2G Here G is average number of frames generated during one…

Q: Consider the scenario shown below, with 10 different servers (four shown) connected to 10 different…

A: The pairs share a common middle hop with a transmission capacity of R = 200 Mbps. Each link from a…

Q: Computer A is sending a 100 kByte long file to Computer B via packet-switching over two consecutive…

A: Here in this question we have given that A is sending a 100 kByte long file to Computer B via packet…

Q: Consider a client and a server connected through one router. Assume the router can start…

Q: Suppose the round-trip propagation delay for Ethernet is 46.4 µs. This yields a minimum packet size…

A: Let's Assume 48 bits of the jam signal, it was still used.

Q: In this problem you will be doing some elementary calculations of transmission and propagation…

A: In-Store and forward transmission, the packet switch must receive an entire packet bits before…

Q: Suppose users share a 2 Mbps link. Also suppose each user transmits continuously at 1 Mbps when…

A: Total transmission rate= 2Mbps Minimum transmission rate required by each user = 1Mbps So it will be…

Concept explainers

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.

Question

Q. Determine the efficiency of a token ring with a data rate of 250Mbps, a ring latency of
120 µsec and 5000 bit packets. Assume N hosts want to transmit and each host holds the token for a maximum of frame transmission time.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Suppose that there are three inter-media nodes between Host 1 and Host 2, and the transmission rate of each link is 4.096 Mbps. The time of end-to-end circuit established is 0.5 second. How much seconds does it take to send a file of 8.192M byte from host H1 to host H2 over a packet-switched network?
Computer Science Assume the length of each message is L=5, the access link has a speed of X=180 Mbps, and there are B=6 messages per second on average. What is the total average delay for receiving a message when no cache is used, i.e., the sum of LAN delay, access delay, and internet delay? Give your answer in milliseconds.
2.Consider a point-to-point link 50 km in length. At what bandwidth would propagation delay (at a speed of 2 × 108 m/sec) equal transmit delay for 100 - byte packets? What about 512-byte packets?.
This elementary problem begins to explore propagation delay andtransmission delay, two central concepts in data networking. Consider two hosts, Aand B, connected by a single link of rate R bps. Suppose that the two hosts areseparated by m meters, and suppose the propagation speed along the link is smeters/sec. Host A is to send a packet of size L bits to Host B. g. Suppose ? = 2.5?108, L=1500 bytes, and R=10 Mbps. Find the distance m sothat ????? equals ??????.
Use again the network architecture provided in the figure above, were RS, RC and Ri for i = {1,2,3,4}, the transmission rates of the server link, client link and intermediate network links. Consider a message that is 60 · 106 bits long that is to be sent from client to server. Ignore propagation, queuing, and processing delays. a.Now assume that Rc = 60Mbps, Rs = 40Mbps, R1 = R3 = 30Mbps, R2 = 10Mbps and R4 = 20Mbps. Suppose that the message is segmented into 6000 packets, with each packet being 10,000 bits long. How long does it take to move the first packet from source host to the first switch? When the first packet is being sent from the first switch to the second switch, the second packet is being sent from the source host to the first switch. At what time will the second packet be fully received at the first switch? b) How long does it take to move the file from source host to destination host when message segmentation is used if path R3, R4 is chosen?
This elementary problem begins to explore propagation delay and transmission delay, twocentral concepts in data networking. Consider two hosts, A and B, connected by a single link ofrate R bps. Suppose that the two hosts are separated by m meters, and suppose the propagationspeed along the link is s meters/sec. Host A is to send a packet of size L bits to Host B.a. Express the propagation delay, dprop, in terms of m and s.b. Determine the transmission time of the packet, dtrans, in terms of Land R.c. Ignoring processing and queuing delays, obtain an expression for the endto-end delay.d. Suppose Host A begins to transmit the packet at time t = 0. At time t = dtrans,where is the last bit of the packet?e. Suppose dprop is greater than dtrans. At time t = dtrans, where is the first bit ofthe packet?f. Suppose dprop is less than dtrans. At time t = dtrans, where is the first bit ofthe packet?g. Suppose s = 2.5 · 108, L = 120 bits, and R = 56 kbps. Find the distance mso that dprop equals…
Suppose that R = 1 Gbps and Rc is 300 Mbps and Rs is 200 Mbps. Assuming that the servers are sending at their maximum rate possible, enter the link utilization of the shared link, whose rate is R, below. Enter your answer as a decimal, of the form 1.00 (if the utilization is 1, or 0.xx if the utilization is less than 1, rounded to the closest xx).
2. Question; Consider two hosts, A and B, connected by a single link of rate R bps. Suppose that the two hosts are separated by m meters, and suppose the propagation speed along the link is s meters/sec. Host A is to send a packet of size L bits to Host B. Express the propagation delay, ????? , in terms of m and s. Determine the transmission time of the packet, ?????? , in terms of L and R. Ignoring processing and queuing delays, obtain an expression for the end-to-end delay. Suppose , ? = 2?10^8 ?/?, ? = 5 ????? and ? = 100???? Find the distance m so that ????? equals ??????.
Assume a 10Mbps Ethernet has two nodes, A and B, connected by a 360m cable with threerepeaters in between, and they each have one frame of 1,024 bits to send to each other. Further assumethat the signal propagation speed across the cable is 2*10^8 m/sec, CSMA/CD uses back-off intervals ofmultiples of 512 bits, and each repeater will insert a store-and-forward delay equivalent to 20-bittransmission time. At time t=0, both A and B attempt to transmit. After the first collision, A draws K = 0and B draws K = 1 in the exponential back-off protocol after sending the 48bits jam signal. a. What is the one-way propagation delay (including all repeater delays) between A and B inseconds? At what time is A's packet completely delivered at B? b. Now suppose that only A has a packet to send and that the repeaters are replaced with switches.Suppose that each switch has an 8-bit processing delay in addition to a store-and-forward delay.At what time, in seconds, is A's packet delivered at B?
Calculate the total time (in milliseconds) required to send a file of size of 8000 Bytes. Assume one-way propagation delay of 40 milli second on a link with bandwidth of 0.8 x106 Bytes/second and a packet size of 1000 Bytes where data packets can be sent continuously with no packet loss.
3.4-7 Stop-and-wait: channel utilization. Suppose a packet is 10K bits long, the channel transmission rate connecting a sender and receiver is 10 Mbps, and the round-trip propagation delay is 10 ms. What is the maximum channel utilization of a stop-and-wait protocol for this channel?
Assume that an end-to-end communications system is made up of three networks with date rate in Mbps ρ1, ρ2, and ρ3, respectively. Ignoring the other delay components, what is the total end-to-end delay to transmit a packet size of λ?