Please help me with question (b) which s linked from (a) Determine the hydrostatic force on the bottom of a tank3 x 3,6 x 3 m if filled with water to a height of 2,4 monly.(254,3 kN)If the tank in Question (a) is sealed on top and thespace is filled with air at a pressure of 20 kPa, whatwill the hydrostatic force then be?(470,3 kN)

Answered: Image /qna-images/answer/cf432777-124a-4846-9e8f-2cba318a734d.jpg

Determine the hydrostatic force on the bottom of a tank 3 x 3,6 x 3 m if filled vith vater to a height of 2,4 m only. (254,3 kN) If the tank in Question (a) is sealed on top and the space is filled with air at a pressure of 20 kPa, what will the hydrostatić force then be? (470,3 kN)

Determine the hydrostatic force on the bottom of a tank 3 x 3,6 x 3 m if filled vith vater to a height of 2,4 m only. (254,3 kN) If the tank in Question (a) is sealed on top and the space is filled with air at a pressure of 20 kPa, what will the hydrostatić force then be? (470,3 kN)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: Derive the formula used in determining experimental hydrostatic force using the center of pressure…

Q: HYDROSTATIC FORCE ON CURVE SURFACE AN EMPTY TANK WAS THROWN IN A BODY OF FLUID WITH sg = 0.8. IF THE…

A: In the given condition, the upward thrust of force acting on the tank due to weight of the tank…

Q: A semi-circular vertical plate is partially submerged in the water as shown in the figure. What is…

A: Find the force on the plate due to hydrostatic pressure.

Q: The dam in Fig. P is a quarter circle 50 m wide into thepaper. Determine the horizontal and vertical…

A: Given: The width of the dam, w = 50 m The radius of the dam, r = 20 m

Q: H.W2: The tank in Fig. is 40cm wide. Determine the hydrostatic forces on horizontal plan BC and AD?…

Q: Air Question 5. 1,2 m wide AB gate is articulated from point A shown in the figure. The heights of…

A: Given: Width of the gate is 1.2 m. Gauge pressure measured is -10 kN/m2. SG of oil is 0.75.

Q: Find the magnitude of the hydrostatic force acting on the curve AB? (Density of w kg/m3) Surface is…

A: Givenl=1msurface is 1mh¯=1+12=1.5mIG=1×1312=112

Q: 1. In the figure shown, a vertical triangular gate submerged in a certain liquid with s.g. = 0,85.…

A: GIVEN :- A vertical triangular gate.s.g.=0.85e=150 mmρ=850 kg/m3h=2.7 mb=1.2 m SOLUTION :- here,…

Q: Problem 3 A gate is 1.5m in wi dth and hinged at point A. Another point on the gate, B. is resting…

Q: Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate, B, is resting…

Q: watersurface. 1-3 m hinged gate P 3 m

Q: 1. The plane surface AB in the figure is rectangular in shape, 3 m wide, an d5 m long perpendicular…

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: Q4/ A4-m-long curved gate is located in the side of a reservoir containing water as shown in Fig.…

Q: The Hoover Dam, in Arizona, encloses Lake Mead,which contains 10 trillion gallons of water. The dam…

A: Consider the diagram shown below for the given dam. Given data:

Q: In the pressurized oil tank (p = 60 kPa gage), a triangular gate ABC is pivoted along the lower…

Q: A 65-cm-diameter circular gate as shown in the figure (dimensions are not to scale) is located in a…

Q: Determine (a) the total hydrostatic force on the curved surface AB in the figure and (b) its line of…

A: Given: The depth of water, h = 20 m The radius of gate, R = 20 m

Q: Gate ABC is a circular arc, sometimes called a Tainter gate ,which can be raised and lowered by…

A: Given data as per the question radius = 6 m calculations

Q: Q2/ The dam in Fig. below is a quarter circle 50 m wide into the paper. Determine the horizontal and…

A: Given data specific weight of water (γwater) = 9790 N/m3 radius of quarter circle (r) = 20 m Width…

Q: A 65-cm-diameter circular gate as shown in the figure (dimensions are not to scale) is located in a…

Q: The hemispherical dome in Fig. (4) weighs 30 kN and is filled with water and attached to the floor…

Q: Calculate the fluid force on one side of a 5 ft by 5 ftsquare plate if the plate is at the bottom of…

A: Given data:- Side of square, a=5ft.=1.524m ∴ Area of square, A=a2=2.32m2 depth of water=8ft.=2.4384m…

Q: A hypodermic syrtnge contains a medcine with the density of water (fgure below). The barrel of the…

A: Given: F=1.72 N

Q: Q2/ The dam in Fig. below is a quarter circle 50 m wide into the paper. Determine the horizontal and…

Q: H.W2: The tank in Fig. is 40cm wide. Determine the hydrostatic forces on horizontal plan BC and AD?…

Q: A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, as shown in…

Q: 1 Calculate the resultant of hydrostatic force on the gate. What vertical force P is necessary to…

A: Given, Weight of the gat e, W =800 N Width of the gate, b =1.6 m

Q: A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in…

A: Given datar=2fth=15 fthinged at point ATo find1) hydrostatic force2) weight of cylinder per ft…

Q: A rectangular watertight box (of treasure) is 660mm long. 520mm wide and 310mm deep. It weighs 323N.…

A: Given Length L= 660 mmW=520mmd=310 mmWeight Wt=323 N

Q: Derive the expression for the hydrostatic force on a vertical plane surface?

A: Given: A Vertical plane surface is given which has area 'A' and gravitational acceleration ' g '

Q: find a) the total force on gate AB in KN and b) the position of the center of pressure in m with…

Q: Consider a wooden cylinder (SG = 0.6) 1 m in diameterand 0.8 m long. Would this cylinder be stable…

A: Given data: The specific gravity of wooden cylinder, SG = 0.6. The diameter of cylinder is, d = 1…

Q: A car, travelling from Kangar to Padang Besar, has met an accident near the dam. The driver has…

Q: In Fig. , a one-quadrant spherical shell of radius R issubmerged in liquid of specifi c weight γ and…

A: Given Radius = R Specific weight = γ Depth h >R To find Expression for the resultant hydrostatic…

Q: 2) The tank in the figure shown has a 4-cm diamter plug which will pop out if the hydrostatic force…

Q: A cylinder is formed by bolting two semicylindrical channelstogether on the inside, as shown in Fig.…

A: Apply the Bernoulli equation to find surface pressure.

Q: A tank of water (SG = 1.0) has a gate in its vertical wall 5 mhigh and 3 m wide. The top edge of the…

A: Here b=width of gate=3mh=height of gate=5 mSo the area of the gate isA=b×hA=3×5A=15 m2Centroid is…

Q: The cap at point B on the 5-cm-diameter tube in Fig.will be dislodged when the hydrostatic force on…

A: Given data: The diameter of the smaller tube, d = 5 cm. Force acting to dislodged the cap at point…

Q: Water. 20°C 4m He. 20 3m H.W3 water in a tank is pressurized to 85cmHg as show in Fig. Determine the…

A: The hydrostatic force on panel AB is to be calculated The pressure at the interface of water Po and…

Q: Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate. B. is resting…

A: GIVEN :- Width of the gate : b=1.5 m specific gravity of sea water : sg=1.03 SOLUTION :-…

Q: A vertical circular gate ABC is 4 m in diameter and is hinged at B, the middle of the gate. When h =…

Q: A plane area of 80 cm 80 cm acts as an escape hatch on a submersible in the Great Lakes. If it is on…

Q: The hemispherical dome in Fig. weighs 30 kN and isfi lled with water and attached to the fl oor by…

A: Assuming no leakage, the hydrostatic force required equals the weight of missing water,…

Q: Q-5 The dam in Fig. is a quarter circle 50 m wide into the paper. Determine the horizontal and…

Q: Determine the resultant hydrostatic force on the 1 m square door shown in the figure below, and the…

A: absolute reading of the guage = patm = po+P mercury = 50 KPa + 13.6 *9.81*0.5 = 116.7 KPa

Q: An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its…

Q: Express the hydrostatic force against one side of the plate as an integral and evaluate it.

A: Given: A hemispherical plate d=10 ft d=1 ft Density = 62.5 lb/ft3 To determine: The hydro-static…

Q: 2- A semicircular 30-ft-diameter tunnel is to be built under a 150-ft-deep, 800-ft-long lake, as…

Concept explainers

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.

Question

100%

Please help me with question (b) which s linked from (a)

Determine the hydrostatic force on the bottom of a tank
3 x 3,6 x 3 m if filled with water to a height of 2,4 m
only.
(254,3 kN)
If the tank in Question (a) is sealed on top and the
space is filled with air at a pressure of 20 kPa, what
will the hydrostatic force then be?
(470,3 kN)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Defining the problem

VIEW

Solution of part a and b

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Water in a tank is pressurized to 140 cm Hg, as shown in the figure. Determine the hydrostatic force per meter width on panel AB.
In Fig. , vertical, unsymmetrical trapezoidal panelABCD is submerged in fresh water with side AB 12 ft belowthe surface. Since trapezoid formulas are complicated,( a ) estimate, reasonably, the water force on the panel, in lbf,neglecting atmospheric pressure. For extra credit, ( b ) lookup the formula and compute the exact force on the panel.
An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged
Gate ABC is a circular arc, sometimes called a Tainter gate ,which can be raised and lowered by pivoting about point O .See Fig.. For the position shown, determine ( a ) thehydrostatic force of the water on the gate and ( b ) its line ofaction. Does the force pass through point O ?
The dam in Fig. P is a quarter circle 50 m wide into thepaper. Determine the horizontal and vertical componentsof the hydrostatic force against the dam and the point CPwhere the resultant strikes the dam.
The Hoover Dam, in Arizona, encloses Lake Mead,which contains 10 trillion gallons of water. The dam is1200 ft wide and the lake is 500 ft deep. ( a ) Estimate thehydrostatic force on the dam, in MN. ( b ) Explain howyou might analyze the stress in the dam due to this hydrostaticforce.
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
Calculate the fluid force on one side of a 5 ft by 5 ftsquare plate if the plate is at the bottom of a pool filled with waterto a depth of 8 ft anda. lying flat on its 5 ft by 5 ft face.b. resting vertically on a 5-ft edge.c. resting on a 5-ft edge and tilted at 45° to the bottom of the pool
A tiny steel cube is suspended in water by a string. If the lengths of the sides of the cube are very small, how would you compare the magnitudes of the pressures on the top, bottom, and side surfaces of the cube?
Hydrostatic: A 2-m-wide, 3-m-high vertical rectangular gate has its top edge 2 m below the water level. It is hinged along its lower edge. What force, acting on the top edge, is necessary to hold the gate shut?
A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in the figure below. When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens. (b) the weight of the cylinder per ft length of the cylinder.