Determine the input and output impedances for a non-inverting amplifier with R, = 560 kn and R; = 2.7 k. The Op-Amp used has Ao1 = 175,000, Zin = 10 M, and Zout = 75 0. Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.

Determine the input and output impedances for a non-inverting amplifier with R, = 560 kn and R; = 2.7 k. The Op-Amp used has Ao1 = 175,000, Zin = 10 M, and Zout = 75 0. Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

What is the cut–off frequency of an op-amp if the unity-gain frequency is 2.8 MHz and the open-loop gain is 200,000? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below. ASAP.
What is the cut–off frequency of an op-amp if the unity-gain frequency is 2.8 MHz and the open-loop gain is 200,000? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.
An operational amplifier has a high input impedance and low output impedance. Do you think having those impedance are good or not? Explain your answer.
For the op-amp circuit as shown below, given that RS = 46 kΩ, RL = 15 kΩ, R1 = 15 kΩ, R2 = 11 kΩ, R3 = 6.5 kΩ, R4 = 2.5 kΩ, R5 = 3 kΩ.
What are the voltage gain, input resistance, andoutput resistance of the amplifier as shownif R1 = 8.2 k ohm and R2 = 750 k ohm ? Express thevoltage gain in dB.
An operational amplifier has a very high gain. Do you think having a very high gain is good or not? Explain your answer.
A cascade amplifier is to be designed to meet these specifications: Aυ = 5000 Rin ≥ 10 MΩ Rout ≤ 0.1 Ω How many amplifier stages will be required if the stages must use an op amp below? Because of bandwidth requirements, assume that no individual stage can have a gain greater than 50. Op amp specifications: A = 85 dB Rid = 1 MΩ Ro = 100 Ω Ric ≥ 1 GΩ
For an op-amp having a slew rate SR = 8 V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.5 V in 10 ms? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.
An amplifier operating over the frequency range of 455 to 460 kHz bas a 200-kῼ input resistor. What is the rrns noise voltage at the input to this amplifier if the ambient temperature is 17°C? Repeat for a) series combination of 3 such resistors and b) parallel combination of 3 such resistors.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the following:A. Gain of amplifier when the feedback was addedB. Percent reduction in distortion when feedback was addedC. The voltage required in the input of the amplifier in order that output voltage is the same as the voltage without feedback
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the voltage required in the input of the amplifier in order that output voltage is the same as the voltage without feedback
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the percent reduction in distortion when feedback was added