Determine the magnitude of the series impedance parameters of Transformer(Req ,Xeq) referred to the primary side of the equivalent Circuit. 2-Draw the equivalent circuit of single-phase Transformer ,and write each value on it. ? 3- Draw the Experimental setup of the short - circuit Test.

Determine the magnitude of the series impedance parameters of Transformer(Req ,Xeq) referred to the primary side of the equivalent Circuit. 2-Draw the equivalent circuit of single-phase Transformer ,and write each value on it. ? 3- Draw the Experimental setup of the short - circuit Test.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.14P: A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Related questions

Q: Find thevenin's equivalent with respect to terminal "ab

A: This question belongs to electrical circuit theory . It is based on the concept of Thevenin's theore...

Q: P6- Using the dual of Millman's theorem, find the current through RL for the networks: 4A 1.6A 8A 8m...

A: The solution is given below

Q: subject: Circuits II A 50 -cycle current has a maximum value of 5.0 amps. What will be the instantan...

Q: A-Using nodal analysis, find VO in the circuit in Fig 3 V 1Ω

Q: Find the resistance of a conductor at 500 degrees Celsius given that its temperature coefficient at ...

A: 1. It is given that: R1=200 ΩT1=420°CT2=500°CT=0°Cα=1420/°C

Q: Power rating of a motor drawing a current of 40 A at 400 V is?

A: Given: A motor drawing a current, I = 40 A At voltage, V = 400 V

Q: For the transfer function HCs)- St 30 5243342 find tre nesporse due to xlt) = Sinat) uct) %3D

A: GivenH(s)=s+10s2+3s+2x(t)=sin2tu(t)

Q: 3Ω 3Ω 15 V 4 A

A: For the calculation of Norton resistance We need to replace the voltage source by short circuit bran...

Q: 6. The field winding of a DC generator is wound with 900 turns and has a resistance of 50 ohms. If t...

Q: Realize the following function using only two-input NAND gates. F = B(A'C' + D) + (A + B'D')C.

Q: 23 W compact fluorescent lamp (equivalent to a 100 W incandescent lamp) remains lit for 12 hr a day ...

Q: Total capacitance of two capacitors of 20 mF connected in parallel will be:

A: Given that Two capacitors of 20mF are connected in parallel. Find the equivalent capacitance of tho...

Q: A-Using nodal analysis, find VO in the circuit in Fig 32 3 V 1Ω (+ I)

Q: The noise produced by à résištör is to be amplified by a noiseless amplifier having a voltage gain o...

Q: 1. Choose one type of diode and explain its function, operation, and different applications. Your ...

Q: Determine the noise current for a diode with a forward bias of 45.15 mA over a 100 kHz bandwidth. a....

A: For a diode - The forward bias current is,IFD=45.15mAThe bandwidth is,BW=100kHz

Q: Total capacitance of two capacitors of 20 mF connected in parallel will be:

A: Given: Two capacitors of 20 mF connected in parallel.

Q: he Illumination at any point of surface is , to the cosine of angle the luminous flux makes with the...

A: The illumination at any point of surface is directly proportional to the cosine of angle the luminou...

Q: 10) Calculate the current through each resistor and voltage across each resistor. 32 0 50 0 200 + 30...

A: Given circuit,

Q: Consider an input x[n] and a unit impulse response h[n] of a discrete-time LTI system given by: h[n]...

Q: The Norton current at terminals a-b in the circuit -j2 Q o a 6/0° V j42

Q: 12 a ww 32 V 12 2 2 A RL Copyright O McGraw-Hill Education. b ww

Q: 2-Draw the equivalent circuit of single-phase Transformer ,and write each value on it. ?

Q: Power rating of a motor drawing a current of 40 A at 400 V is?

A: This question belongs to electrical machine . It is based on calculation of power rating of machine...

Q: Consider the system defined by i = Ax + Bu y = Cx 1 where, A = 1 -6 -11 -6 B= |0| and C = [10 5 1] C...

Q: Q1) Reduce the block diagram shown below and write the transfer function C(s) /R(s) Cls) G2 (s) Ge G...

Q: 4.8.2 In the circuit shown in the image below, if V1 = 4.2 V and R1 = 4.9 Q, according to the superp...

Q: prove in Parkial dereuation Cis)= =- (2/7)+

A: In this question, We need to prove that the partial fraction of the given system. This function is ...

Q: If A, B, and C are the inputs of the given circuit then determine the output waveform X. Circuit di...

A: In this question, A, B, and C are the inputs of the given circuit then determine the output wavefor...

Q: 2.5 For the circuit shown in Fig. 7, the value of R2 is required to be measured. Why doesn't such a ...

A: Given: Value of 'R2' is required to measure.

Q: The following is configured on a router Router(config)# interface g0/0.10 ...

A: On a router - The following instructions is set up, Router(config)# interface g0/0.10 Router(config-...

Q: 2. Find the total current of the charge graph below q (C) A 10 1 2 4 t(s)

A: Given

Q: 1. An emf of 9.7mV is induced in a coil while the current in a nearby coil is decreasing at a rate o...

A: We need to find out mutual inductance for given induced voltage

Q: A 300- kw alternator has an efficiency of 90 % at full load. Calculate the power losses? 267 kw 27 k...

Q: 2.A three-phase, three-wire system, with an effective line voltage 100 V, has currents IA Ic = 15.41...

A: This question belongs to electrical power system . It is based on the concept of delta connected bal...

Q: A band pass filter is to be constructed using RC components that will only allow a range of frequenc...

Q: 1. Design the voltage divider of Figure 1 such that VRI = 4VR2. 20 V Figure 1

Q: input of a Low Pass Filter (LPF) is White Noise (all the frequencies at the same intensity e.g. 0dB)...

Q: 20.a. A –3.8 dBm optical signal exits an amplifier with a signal strength of 15.1 dBm. How much gain...

Q: When solving in AC Analysis, a negative sign in the voltage or current gain means that the output is...

A: When we get negative sign in output voltage it means that output is 180 degrees out of phase to inpu...

Q: 1) Calculate the current (I) in the following circuits using mesh analysis. 10 2 6 V 6 V 42 12 ww 12...

Q: Find (1) (iii) 1 (iv) 1011111010.102 by 11012

Q: 50 10Ω 4Ω 5 io 5 i, v 20 N v§ 40 N v 96 V 11.5 i,

Q: Explain anyone practical measurement system with all of its functional elements.

A: Functional elements of practical measurement system:

Q: Given A = -4a, + 2a, + 3a, and B = 3ax + 4ay - az, find: a. The magnitude of 5A - 2B b. A unit vecto...

Q: Predict how the operation of this clipper circuit will be affected as a result of the following faul...

A: In the positive half cycle of input , the diode should be On ( means diode acts as short ) Output is...

Q: 9. Using hybrid model, find the Zo of the whole circuit if Vo = -200. 20 V hfe = 140 hie = 0.86kohms...

A: Hybrid parameters hib=input impedance with output short circuit hrb=Reverse voltage ratio input open...

Q: Use superposition to find the voltage v, in the circuit shown. 3 A 10Ω ww + V, 40 V (+ 10 Ω 2V

A: In this question, We need to calculate the voltage Vx in the given circuit using the super position...

Q: When the load impedance is equal to the characteristic impedance of the transmission lines, then the...

Q: tance total Impedanee total Capaci

A: Inductance is series- Leq=L1+L2+......Inductance in parallel-1Leq=1L1+1L2+...... Capacitance in para...

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

I need answer within 20 minutes please please with my best wishes Hussein

Determine the magnitude of the series impedance parameters of
Transformer(Req ,Xeq) referred to the primary side of the equivalent Circuit.
2-Draw the equivalent circuit of single-phase Transformer ,and write each value on
it. ?
3- Draw the Experimental setup of the short - circuit Test.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer has a 1-ohm equivalent leakage reactance and a 5000-ohm magnetizing reactance referred to the high-voltage side. If rated voltage is applied to the high-voltage winding, calculate the open-circuit secondary voltage. Neglect I2RandGc2V losses. Assume equal series leakage reactances for the primary and the referred secondary.
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) False
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
Consider the adopted per-unit system for the transformers. Specify true or false for each of the following statements: (a) For the entire power system of concern, the value of Sbase is not the same. (b) The ratio of the voltage bases on either side of a transformer is selected to be the same as the ratio of the transformer voltage ratings. (c) Per-unit impedance remains unchanged when referred from one side of a transformer to the other.
A three-phase transformer is rated 1000MVA,220Y/22kV. The Y-equivalent short-circuit impedance, considered equal to the leakage reactance, measured on the low-voltage side is 0.1. Compute the per-unit reactance of the transformer. In a system in which the base on the high-voltage side of the transformer is 100MVA,230kV what value of the per-unit reactance should be used to represent this transformer?
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
Given:A single-phase two-winding transformer is rated 20 kVA, 480/120 volts, and 60 Hz. The equivalent leakage impedance of the transformer referred to the 120-volt winding,denoted winding 2, is ???2 = 0.0525∠78.13°?.Find:Using the transformer ratings as base values, determine the per-unit leakage impedance referred to winding 2 referred to winding 1.
A three phase Y/A transformer rated at 50 MVA, 230/34.5 kV is to be protected using biased differential circulating current protection scheme. The CT ratio at the high voltage and low voltage side are 250/5 and 900/5 respectively. Draw the protection scheme and determine the current at both side of the transformer.
A 300-kVA, 460-V, balanced three-phase load is supplied by three single phase transformers connected in Δ/Y to form a three-phase transformer. The primary winding of the three-phase transformer is connected to a 4.8 kV, three-phase transmission line. Determine (a) the rated primary voltage and current, (b) the rated secondary voltage and current, and (c) the power rating of each transformer. -What are the primary and secondary line currents?