Answered: Determine the maximum compressive…

Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is applied at x = 300 mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.14P: Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82...

See similar textbooks

Related questions

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown,…

A: Considering the equilibrium of femur,

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

Q: Determine the magnitude of the load P that will cause a maximum normal stress of smax = 30 ksi in…

A: Draw the free-body diagram of the structure.

Q: During the tension test, the wooden specimen is subjected to an axial force (P = 4 kip) applied to…

A: Given data Force (P) = 4 kip

Q: If the allowable normal stress for the bar is s allow = 120 MPa, determine the maximum axial force P…

A: Write the given data:

Q: Determine the principal stresses at point A on the cross-section of the beam at section a-a

Q: The clamp shown is made of members AB and AC, which are pin-connected at A. If it exerts a…

Q: 2.2 (A) If the maximum stress allowed in the copper of the cabic of problem 2.I is 60 MN/m2,…

A: Given: Area of cross-section of the cable=6×10-5m2 Maximum allowable stress=60MN/m2 Maximum tension…

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A: GIVEN:temperature dropped =-40'Fapplied load=20 kipE=29X106 psiα=6.5X10-6/'Flength of AB=4ftlength…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 16 mm. Assume…

Q: The frame supports the distributed load shown. Determine the state of stress acting at point D. Show…

A: In this problem, the state of stress at point D is determined by drawing the FBD as discussed in the…

Q: For the given truss system, determine the normal stress in member BE if its cross sectional area is…

Q: Determine the maximum normal stress in the block at any possible orientation.

Q: The bars of the truss each have a cross-sectional area of 1.25 in2. If the maximum average normal…

A: Given data: The cross-sectional area of the bar is; A = 1.25 in2. The maximum stress in the bar is;…

Q: The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial…

A: To Find : the normal stress in the rod at x=0.5m Given : cross sectional area of rod A=410mm2…

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: The given bar is critical to two positions:1) At the fillet section2) At the hole sectionAt fillet…

Q: 4. A load P is applied concentrically to the bar shown. If the allowable normal stress is 76 ksi,…

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-16 aluminum. If a couple forces P =…

A: As applied force is at some distance from the longitudinal axis. so it generates torque and the…

Q: 1. The bars of the pin-connected frame are each 300 x GOo mm in section. Determine the maximum bad P…

A: Given, A truss structure . Area of the bar , A =300*600 mm = 0.18 m2. Maximum tensile stress ,…

Q: O: If the allowable bearing stress for the material under the supports at A and B is (Gallow) = 1.5…

A: Answer: The maximum loaf P that can be applied to the beam is 72.5 kN.

Q: The hanger is supported using the rectangular pin. Determine the required thickness t of the hanger,…

Q: The post has a circular cross section of radius c. Determine the maximum radius e at which the load…

A: The axial compressive stress on the post is

Q: Determine the maximum compressive stress in the bracket at section a-a when the load P = 25 kN is…

A: Given: The load, P = 25 kN The distance of load acting from one end, x = 300 mm

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

Q: Determine the maximum compressive stress in the bracket at section a-a when the load P = 70 kN is…

A: Given that , P=70kN at x=0

Q: Load P shown below can be applied at any point on the steel disc (r=40mm) shown below. For this…

A: Given

Q: b. Determine the maximum value of the average normal stress points C and E. 0.4 m c. Determine the…

A: Here we have given P=20 kNdiameter d= 16mm∑mB=020(0.25)=-FCE(0.4)FCE=-12.5 kN (compr)

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 12 mm. Assume…

Q: The 3.0-Mg concrete pipe has a center of mass at point G, and is suspended from cables AB and AC.…

A: Given Data Diameter of AB is :dAB=12 mm Diameter of AC is : dAC=10 mm Now draw the force diagram

Q: : The rod weighs 22 lb/ ft and has a diameter of 3 in. Determine the torsional stress at points A…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a-a.

Q: Determine the required thickness of member BC and the diameter o the pins at A and B if the…

Q: F E 2 m A B 2 m 1 m 1m

Q: The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: Q10: Determine the maximum load P (in kN) that can be applied if the normal stress on plane AC must…

A: Given:b=54 mmd=110 mmh=284 mmE=3 GPav=0.45θ=70°σmax=18 MPa

Q: If the allowable bearing stress for the material under the supports at A and Bis op = 820 psi,…

Q: 2. The coping saw has an adjustable blade that is tightened with 8 mm a tension of 40 N. 3 mm A 75…

Q: 2.2 (A). If the maximum stress allowed in the copper of the cabie of problem 2.1 is 60 MN/m?,…

A: Given, The diameter of a single copper wire, d=1.6 mm No. of wires are 10 and there are such three…

Q: Determine the principal stresses in the cantilevered beam at points A and B.

A: Draw sketch of beam and divide shear force into horizontal and vertical components.

Q: (8) The homogeneous bar is supported by a smooth pin at C a cable that runs from A to B around the…

Q: The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm…

A: Given data as per question P = 80KN The thickness of plate =10 mm Area=10×200=2000 mm2 we know…

Q: Member (1) has an area of 2,200.00 mm2 and an allowable normal stress of 180.00 MPa. Member (2) has…

Q: The boom DF of the jib crane and the column DE have a uniform weight of 750 N/m. If the hoist and…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is applied at x = 300 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
A simple truss is subjected to a vertical load F = 500 lb.Determine the minimum diameter of the pin at C if theallowable shear stress on the pin is 20 psi.Answers: d =___________________
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2. The cross-sectional area of rod (2) is 18 mm2. For a uniformly distributed load of w = 2.4 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.25 m.
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. hiii pls help urgenttt ty
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPa. Present detailed drawings/FBD’s illustrating your solution.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
Determine the required diameter (in inches) of rod AC if the allowable normal stress is 24.95 ksi and P = 12.61 kips.