Find correct answer ITS URGENT ASCAP Determine the maximum, minimum and average pressure in a plate clutch when theaxial force is 4kN. The inside radius of the contact surface is 50 mm and the outsideradius is 100 mm. Assume uniform wear.

Given data; Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Answered: Determine the maximum, minimum and…

Engineering

Mechanical Engineering

Determine the maximum, minimum and average pressure in a plate clutch

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.
An automotive plate clutch consists of two pairs of contacting surfaces with asbestos friction lining. The maximum engine torque is 200 N-m. The coefficient of friction is 0.35. The inner and outer diameters of friction lining are 200 and 300 mm respectively. Clamping force is provided by nine springs, each compressed by 4 mm to give a force of 700 N, when the clutch is new.(i) What is the factor of safety with respect to slippage when the clutch is brand new?(ii) What is the factor of safety with respect to slippage after initial wear has occurred?(iii) How much wear of friction lining can take place before the clutch will slip?
the power transmitted by a single plate clutch at a speed of 2000 rpm, if the outer and inner radii of Triction surfaces -are 150 mm and 100 mm respectively. The maximum intensity of pressure at any point of contact surface should-not exceed 0.8 x 105 N/m2. Take both sides of the plate as effective and coefficient of friction = 0.3. Assume uniCalculateform wear.
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2. If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.
The external and internal diameter of a single plate clutch are 125 mm and 100 mm, respectively. It is used to transmit power at limited (maximum) axial pressure of 0.2 MPa. Which of the following is the axial force exerted by the springs? Assume uniform wear conditions. Choices: 790N1960N 440N 980N
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25
Question No.13: A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250mm and inner diameter is 150mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75kW at 500 rpm. Assume uniform wear and coefficient of friction as 0.3.