When the clutch is disengaged, the power flow stops at the

Q: 5- Mention the air fuel ratio required by the engine during (a) Starting time zero load (b) Normal…

A: From the given data,

Q: Describe the purpose of a viscous clutch.

A: Viscous clutch The clutch is part of the machine that is used to operate for the transmission's…

Q: The braking torque on the drum is

A: Given data;    External drum brake is shown in figure.  Diameter,d= 500 mm  Dimensions of the brake…

Q: Among the following, which drive transmits exact velocity ratio during power transmission. Gear…

A: Gear drive

Q: 3. where used the heli cu we springs

A: The helical spring, in which wire is enclosed by a loop that takes after a screw string, is…

Q: H8/e8, the toleran tol de orit of

A:

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. ABS R

A: Hydraulic symbols give a clear representation of the work of each hydraulic component. Laying…

Q: The temperature of the air is 29 °C at the inlet to the comp

A: given:rp=8T1=290cT2=10800ccp=1.006kj/kgkcv=0.717kj/kgk

Q: The high tension side of belt is known as tight side Select one: True

A: Given: Belt pulley system

Q: es. The nozzle a f steam at the e

A:

Q: What type of electromagnetic clutch is used in late model vehicles

A: Electro magnetic clutches also known as electro - mechanical clutches. Because these clutches…

Q: Flat belt can be used as a clutch. Give an example of that with a diagram and explain

A: Flat belt can be used as a clutch....the diagram and explantation are given below

Q: Explain the importance of a cone clutch with an application.

A: Given Data : Cone clutch

Q: controls on/off of the motor, when the air compressor tank reaches the specified bar.

A: Compressed and filtered air enters the tank after coming out of the Air compressor

Q: In this diagram, which pressure differential valve has pressure loss? Which part of the system has…

A: Differential valves are used for detecting differential pressure. detection of the valve failure of…

Q: e power required to drive t e pump.

A: Need to find the power required to drive the pump.

Q: 5. Briefly describe how a double-clutch transmis- sion works.

A:

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: shaft torque (in N-m) sensed by the dynamometer is

A: Given data;  Brake power= 10 kw Speed of shaft= 400 rad/s  Determine the shaft torque sensed by the…

Q: Find the output speed and cycle ra

A: by relation between radius of gear and its RPM findout the output RPM. here, rate of cycle asked…

Q: Describe the operation of a roller-type one-way clutch with diagram

A: Clutch : Clutch is a mechanical device used to transmit power when required (intermittent power…

Q: In cone clutch, the power can be transmitted is increased by increasing the turning angle. O…

A:

Q: n a DCV, this part is designed with lands that channel the flow through the valve to specific ports…

A: DCV is the directional control values used in the hydraulic and pneumatic system, It controls the…

Q: e power output from

A: Need to calculate the power output.

Q: AC det D The balance condition for AC bridges is: Select one: O 1.7,Z,-Z,Z, O 2. R,R,=R,R3 O 3.…

A:

Q: What is the maximum possible speed (i

A: Given: μs=0.60μk=0.30R= 27mno negative lifting forceTo find maximum speed of the car without…

Q: Respond with TRUE if the symbof of the valve shown below is drawn cortectly A 工 R Select one: O True…

A: True or False  The given symbol

Q: The capacity of a clutch depends on the characteristics of the material. Select one: True False

A: Solution:

Q: Determine the maximum, minimum and average pressure in a plate clutch

A: Given data;  Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Q: State the disadvantages of hydraulic transmission systems.

A: Advantages of hydraulic transmission systems:-

Q: In single clutch plate we have ......... ..... pairs of frictional surfaces one O two O three O four…

A: To select the correct option.

Q: The eyclic device can be

A: Given data; T1=1000 KT2=500 KT3=300 KQ1=Q2=Q3=100 KJ=50 KJ=60 KJ respectiveley

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: during what stroke one valve is closed and the piston is moving downward in the cylinder

A: The following diagram shows the processes taking place in an otto cycle.

Q: Determine the Actual Torque Required, TA

A:

Q: Q1: The working pressure is depending on the outside load, if the surface of the piston is 5cm², the…

A: Given data,  m= 10kg  A= 5cm²= 0.0005m²

Q: How are mechanical cooling system clutch fans often engaged? Select one: a. A ratcheting mechanism…

A: Whereas numerous unused vehicles utilize electric cooling fans, numerous more seasoned vehicles…

Q: rom the ov when the in Car Cand theo

A:

Q: enlist the engine operations at the time of both hard acceleration and deceleration and idle.

A: To describe the operation when the engine is accelerating and decelerating.

Q: List three types of clutch linkages used in modem vehicles

A: three types of clutch linkages used in modem vehicles-  The clutch linkage are used for the…

Q: of motion for the syste

A:

Q: List out the applications of compressed air used in oil and gas industries

A: To find:  applications of compressed air used in oil and gas industries

Q: The speed of the wind turbine at which maximum power is generated is called. Select one: O Cut-in…

A: Option (d) Cut-out Speed

Q: In a viscous clutch, when the silicone fluid is heated, it ______.a. becomes a very thin fluidb.…

A: When the silicone fluid is heated in a viscous clutch then the silicon tends to stiffen. This…

Q: A So Find tension in AC and BC Hoola

A:

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.