Drag text boxes to label diagram of a typical valve spring retaining mechanism

Q: Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

A: Camshaft Camshaft is the shaft at which many cams are connected and it operates with the crankshaft.…

Q: What is the force output of a cylinder that has a 1” bore and operated at 600 psig?

A:

Q: Choose the symbol for check valve. Select one: d.

A: Check valves are the devices which allows the flow in only one direction. So, it is also known as…

Q: Draw an indicator and valve-timing diagram for a 4-stroke Sl engine, label it and briefly describe.

A:

Q: the mean output torque and flywheel inertia required for an engine

A: Given:   Cs=0.1 N=1500 rpm To determine: Mean torque Inertia of the flywheel

Q: n. production casing. The maximum expected burst pressure is 14,000 psi. A 17 Ib/gal nud will be…

A:

Q: (c) The type of pressure plate chosen as a result of the calculation in part (b) of this question…

A: A clutch is a device that allows two elements with a common axis of rotation to connect and detach…

Q: If a valve actuator requires 631 PSI to open. What diameter diaphragm is needed if 15 psi of air…

A: I have taken valve actuator requires 631 lbs force to open. Its a mistake in the question

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. ABS R

A: Hydraulic symbols give a clear representation of the work of each hydraulic component. Laying…

Q: Functionality of each compoenent, from prime mover to propeller. List the main propulsive losses and…

A: A prime mover is an engine that converts fuel to useful work. The prime mover is thus the source…

Q: Maximum gas pressure - 3.5 MPa Seat angle – 45° Calculate: (i) diameter of the valve port; (ii)…

A: Given that ;

Q: PROBLEM: A double-acting cylinder is to be used to emboss plastic rulers. The cylinder may only…

A: Given: To find: Components needed

Q: 8. What will be the total piston displacement in a two-cylinder 100 mm x 130 mm engine?

A:

Q: ch of 6 mm. Th d collar friction

A:

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: The factor of safety for the piston rod is

A: Given data; diameter (d) =20mmlength (l)=700 mmforce=10 kNYOUNG MODULUS=200 GPa acc. to question we…

Q: List four possible causes of cluth slippage

A: A Clutch is a mechanical device used in vehicles that transmits power from the motor to the…

Q: Write any 4 types of pneumatic cylinders and draw its symbols?

A: 4 types of pneumatic cylinders- 1) SINGLE-ACTING CYLINDER 2) DOUBLE-ACTING CYLINDER 3) THROUGH ROD…

Q: 1) Draw a simple sketch of your regulator design 2) Draw a simple sketch of the spring

A:

Q: d. Bearing is needed: Shaft rotates at 1400 rpm, subjected to a higher medium radial load in a…

A: Solution:

Q: describe type and properties of spring used in impact of jet apparatus.

A: Solution:

Q: Define Braking loads

A: Braking load/force  is the  frictional force that cats tangentially  between the brake pads and…

Q: Match the symbol to the component: а. Pump b. Motor c. Cylinder with retract cushion d. Pressure…

A:

Q: Match the correct port/hole with its function in a pressure regulator v inlet port A. this is where…

A: As per question  We have to matching correct options

Q: gative loop of the indicator diagram Spring cons,

A:

Q: G) bore and stroke of compressor in mm (k) power of motor to drive the compressor

A:

Q: Assume that after removing the cylinder head of an engine, a wet, oily condition is noticed on the…

A:

Q: Doosan Man 6L60MC-C8 (2 stroke) Engine, piston stroke 2022 mm. Engine maximum power at 108 rpm is…

A: Write the given information.

Q: tail force

A: Tail force is 15kN

Q: Determine the maximum, minimum and average pressure in a plate clutch

A: Given data;  Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Q: What component can be used to increase the speed of pneumatic

A: solution of above problem is  belowL:

Q: 2- Draw theoretical valve timing diagram and compare it with actual one.

A:

Q: what can happen when valve spring tension is too low?

A: When the valve paring tension become low, valve springs will become incapable of holding the valve…

Q: ) What is valve overlap?      b) Why is some amount of valve overlap desirable?  c) Define the term…

A: valve overlap is the number of degrees in the rotation of crankshaft rotation where both the valves…

Q: What type of valve use simple discs, cones or balls are used in conjunction with simple valve seats…

A: A valve is an equipment or natural item that, by opening, shutting, or partially obstructing…

Q: Find K, Cv, and Le for a 3 in Schedule 40 fully open lift check valve. [Ans.: Le = 153 ft].

A: The resistance coefficient, abbreviated as K, is a dimensionless quantity that indicates how much…

Q: Problem 4 CHLA The pneumatic system shown contains a double-rod cylinder controlled by two…

A:

Q: Sketch and explain the valve and port timing diagrams

A: valve and port timing diagrams

Q: Describe a 4-stroke compression ignition engine operation with neat sketches.

A:

Q: List out the design requirements of diesel engine combustion chamber

A: Diesel engines work on the diesel cycle. In diesel engines, the air is compressed alone and at the…

Q: Hydraulic maintenance is done to prevent O a. load lifting capability O b. contamination, leakage…

A: It is required to choose correct Answer

Q: BLOCK DIAGRAM draw the schematic diagram of these components using standard symbols. FLOW CONTROL…

A: The symbolic representation of the block diagram is known as the schematic diagram. Schematics…

Q: Describe uncontrolled spring action without a shock absorber.

A: Function of shock absorber:  A shock absorber is also known as damper. it is a mechanical device…